Quantum StorNext QD6000 Replacing Manual
Controller battery, base system
Hide thumbs
Also See for StorNext QD6000:
- Replacing manual (15 pages) ,
- Site planning manual (30 pages) ,
- Replacing manual (11 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Replacing Manual
Advertisement
Table of Contents
Related Manuals for Quantum StorNext QD6000
Summary of Contents for Quantum StorNext QD6000
- Page 1 Replacing a Controller Battery StorNext QD6000/QD7000 Base System *6-68477-01 Rev A 6-68477-01 Rev A...
- Page 2 USA. ©2016 All rights reserved. Quantum, the Quantum logo, DXi, Scalar and StorNext are registered trademarks of Quantum Corporation and its affiliates in the United States and/or other countries. All other trademarks are the property of their respective owners.
-
Page 3: About This Guide
This section provides the following information: • Intended audience • Prerequisites • NetApp to Quantum Naming Decoder Intended audience This guide is intended for storage customers and technicians. Prerequisites Prerequisites for installing and using this product include knowledge of: • Servers and computer networks •... -
Page 4: Netapp To Quantum Naming Decoder
NetApp to Quantum Naming Decoder Table 1 to correlate the NetApp product nomenclature to the equivalent Quantum-storage naming conventions. Table 1 Product Nomenclature E-Series NetApp Product Quantum-Storage Description Controller-Drive Tray Base System Quantum uses Base System when referring to a drive tray with the RAID controllers. - Page 5 Replacing a Failed Controller Battery in the E5660 Controller- Drive Tray To access this product, go to the NetApp® Support Site at mysupport.netapp.com. You can determine whether you have a failed controller battery in two ways: The Recovery Guru directs you to replace a failed controller battery. The amber Battery Service Action Required LED indicates a failed controller battery.
-
Page 6: Removing A Controller Canister
Removing a Controller Canister ATTENTION Possible hardware damage – To prevent electrostatic discharge damage to the tray, use proper antistatic protection when handling tray components. 1. Gather support data about your storage array by using one of these methods: Use the storage management software to collect and save a support bundle of your storage array. From the Array Management Window, select Monitor >... - Page 7 availability=offline"; 6. Wait for the blue Controller Service Action Allowed LED to come on. For a large configuration, this indication might take several minutes. 7. Put on antistatic protection. 8. Label each cable that is attached to the controller canister with the failed battery so that you can reconnect each cable correctly after the controller canister is reinstalled.
- Page 8 a. Unlock the controller canister release lever, and pull the release lever outward to release the controller canister. b. Using the release lever, pull the controller canister out of the controller-drive tray. Figure 4. Removing and Replacing a Controller Canister 12.
-
Page 9: Replacing A Controller Battery
13. Insert the controller air blocker into the open controller slot to make sure that correct airflow is maintained. Figure 5. Inserting the Controller Air Blocker into the Open Controller Slot Replacing a Controller Battery 1. Unpack the new controller battery. a. - Page 10 Press down on both of the top cover latch buttons as you slide the top cover off the controller canister. Figure 6. Battery and Locking Tab in the Controller 1. Top Cover Latch Buttons 2. Battery Circuit Board 3. Battery Locking Tab 3.
- Page 11 2. Slide the controller canister all the way into the controller-drive tray. Rotate the release levers towards the center of the controller canister to lock it into place. Figure 7. Removing and Replacing a Controller Canister 1. Release Levers 2. Controller Canister 3.
- Page 12 After the controller successfully completes rebooting, the seven-segment display shows the tray ID matching the seven-segment display on the second controller. Figure 8. LED Status aand Seven-Segment Display 1. Controller Service Action Allowed LED (Blue) 2. Controller Service Action Required LED (Amber) 3.
-
Page 13: Trademark Information
Trademark information NetApp, the NetApp logo, Network Appliance, the Network Appliance logo, Akorri, ApplianceWatch, ASUP, AutoSupport, BalancePoint, BalancePoint Predictor, Bycast, Campaign Express, ComplianceClock, Cryptainer, CryptoShred, CyberSnap, Data Center Fitness, Data ONTAP, DataFabric, DataFort, Decru, Decru DataFort, DenseStak, Engenio, Engenio logo, E-Stack, ExpressPod, FAServer, FastStak, FilerView, Flash Accel, Flash Cache, Flash Pool, FlashRay, FlexCache, FlexClone, FlexPod, FlexScale, FlexShare, FlexSuite, FlexVol, FPolicy, GetSuccessful, gFiler, Go further, faster, Imagine Virtually Anything, Lifetime Key Management, LockVault, Manage ONTAP, Mars, MetroCluster, MultiStore, NearStore, NetCache, NOW (NetApp on the Web), Onaro, OnCommand,...