Dimensions And Weight; Electrical Data - Salda RIRS EKO 3.0 1900 HE Mounting And Installation Instruction

Warnings
• Connection of electricity and maintenance of the device should be performed only by a qualified personnel, in accordance with the
manufacturer's instructions and valid safety requirements.
• In order to reduce the risk during installation and maintenance, suitable protective clothes should be worn.
• Beware of sharp angles while performing installation and maintenance tasks.
• Do not touch heating elements until they haven't cooled down.
• Some devices are heavy, thus one should be very careful while transporting and installing. Use suitable lifting equipment.
• While connecting electricity to the mains a circuit breaker of suitable size is necessary.
Warning!
• If the device is installed in a cold environment, make sure that all connections and tubes are properly isolated. Intake and discharge air
ducts should be isolated in all cases.
• Openings of the ducts should be covered during transportation and installation.
• Make sure not to damage the heater when connecting the piping of the water heater. For tightening up, use a wrench/spanner.
Before starting the equipment
• make sure, that there are no strange objects inside;
• manually check whether fans are not stuck or blocked;
• if rotary heat exchanger is installed in the device, make sure that it is not stuck or blocked;
• check the grounding;
• make sure that all components and accessories are connected in accordance with the project or provided instructions.
Danger: Fumes
Salda Antifrost system uses dis-balancing of the air flow and it may cause negative pressure in premises. Great care should be taken H3*
when using at the same time in premises as another heating appliance what depend on the air in premises. Such appliances include
gas, oil, wood or coal-fired boilers and heaters, fireplaces, continuous flow or other water heaters, gas hobs, cookers or ovens which
draw air in from the room and duct exhaust gases out through a chimney or extraction ducting. The heating appliance can be starved
of oxygen, impairing combustion. In exceptional cases harmful gases could be drawn out of the chimney or extraction ducting back
into the room. In this case we strictly recommend to turn off Salda Antifrost and use an external preheater for heat exchanger anti-frost
protection (see Salda Antifrost function on the Remote controller manual).

4. DIMENSIONS AND WEIGHT

L
RIRS H EKO 3.0
[mm]
1200 1350
1900 1350
2500 1610
3500 1900
5500 1910
* - depend on the unit.
m
1200 HE 1200 HW
L3
[kg] 162

5. ELECTRICAL DATA

RIRS EKO 3.0
W2
Heater
4 | EN
W3
L
L1
L
d*
L2*
L1
L1 L2* H H1
W
[mm] [mm] [mm] [mm]
1430 - 900 235
1430 - 900 235
1710 - 1105 285
L3*
2004 - 1302 345
2008 - 1485 390
1900 HE 1900 HW
162 162 350
W1
L2
L1
D*
- phase/voltage
- power consumption
H1
W1
W
H1
W
W1
H4*
H1
H2
H3
W2*
H2 H3 H4* H5*
[mm] [mm] [mm] [mm]
235 70 105 -
H
235 70 105 -
H1
290 140 95 400
L4*
345 140 130 400
390 140 105 500
L1
RIRS EKO 3.0
2500 HE 2500 HW 3500 HE
350 350
L2
1200HE
[50 Hz/VAC] ~2, 400
[kW] 4
H
W2*
H
H2*
H
D*
W3*
D*
H5*
H
H
W2*
L
W W1 W2* W3*
d L5
[mm] [mm] [mm] [mm]
855 428 - -
H2
855 428 - -
1110 555 - 700
1205 600 - 700
1405 700 - 800
3500 HW 5500 HE
492 492 625
1200HW 1900 HE
~3, 400
AVS 315
9
RIRS 1200-5500 H EKO 3.0 v2019.06
øD*
ød*
[mm]
315 -
315 -
- -
- -
- -
5500 HW
625
1900 HW
AVS 315