Select Function - OPTEX FA CD33 SERIES Instruction Manual

Functions of components
CD33-120N(P) CD33-250N(P)
A CD33-120N(P)A CD33-250N(P)A
V CD33-120N(P)V CD33-250N(P)V Control panel
-422 CD33-120N(P)-422 CD33-250N(P)-422
P) CD33-120CN(P) CD33-250CN(P)
P)A CD33-120CN(P)A CD33-250CN(P)A
P)V CD33-120CN(P)V CD33-250CN(P)V
CD33-250CN(P)-
-422 CD33-120CN(P)-422
422
Emitting part
120mm 250mm
m ±60mm ±150mm
length 655nm)
1mW
2
Ⅱ
mm 1.2×1.8mm 1.5×2.5mm
mm 1.0×1.5mm 1.75×3.5mm
mm 0.5×0.8mm 2.0×4.5mm
Receiving part
S. ±0.1% F.S. ±0.3% F.S.
m) (F.S.=120mm) (F.S.=300mm)
30μm 75μm
μm) (Fast：45μm) (Fast：150μm)
max.
7.5ms max.
max. 18ms max.
max.
54ms max.
00 /1500 /2000μs ●Control panel
./℃
LED
Orange
Hold (choose one function)
3ms max.
Over current
ondensation or freezing)
ondensation or freezing)
descent lamp: 3,000 lx max.
1.5 mm, 2 h for XYZ axes
2
/s )
x.
Front window)
out cable)
0g
RS422
③ CD33- ④
4V DC12～24V
%) (+10%/-5%)
mA max. (DC24V)
C
－
x. /30V DC
.)
－
RS422
φ5 8core 2m
G24
cable(PVC) AWG24
he specified spot size.
gets.
tance indicator turns ON ( orange ) at
Distance indicator
Distance indicator has seven LEDs. LED indicate distance by moving at near to far side.
object.
（unit：mm）
reliable measurement (see above).
bject, it may cause incorrect
Ramco Innovations
Fixture Hole
Analogue
･Distance indicator
･Laser emission indication
(ON during laser emission)
Run indicator
Into Teach mode:
function indicator
Control output1
Control output2
MF indicator
Avg indicator
LED lights up , if receiving RS422 command.
Voltage Dual Output
Status of LED Status of measurement
Out of range.
*This LED indicate when due to too
high/low reflection
Object is near of range.
Object is far of range.
Object is some far of range.
Object is middle of range.

Select Function

●Teach mode
①Press the Select button more than 5 seconds.
Fixture Hole
②Teach indicator lights up showing that Run status changes to Teach status.
③Function indicator lights up.
ex.)A type
④Select function by pressing Select button.
ex.)A type
Teach indicator ⑤Adjust or select value of function you need by pressing Set button.
Select button
⑥Then return to RUN by pressing by pressing Select button continuously 5 seconds.
●Special Setting mode
Set button
①Press simultaneously both the Select button and Set button for 5 seconds.
+
RS422
②Both Run and Teach indicators come up.
③Function indicator Q1 lights up.
※Q2 lights up when it's RS422 type.
ex.)A type
④Select a function by pressing Select button.
ex.)A type
⑤Adjust or select the function by pressing Set button.
Indicator
Both side of red LED
lights up
⑥Then return to RUN by pressing by pressing Select button and Set button continuously
Near side of red LED
5 seconds.
lights up
・Control output stops during teaching and setting period while Analog output works.
Far side of red LED
lights up
Reset the presettings
Far side of green LED
Turn on the power by pressing Select button and Set button at the same time and keeping
lights up
them pushed continuously 5 seconds. Then make sure if all the indicator blinks 3 times to
confirm cancel of all presettings.
Middle of orange LED
lights up
800-280-6933 www.optex-ramco.com