Fastener Selection Guide; Installation In Steel - DeWalt P2201 Operating Instructions Manual

Model P2201

installation in Steel

The following guidelines are based on the installation of a
fastener in ASTM A 36 structural steel with the point fully
penetrating the steel member. Recommended steel material
thickness ranges from a minimum of 1/8" to a maximum of
3/8". for use in higher strength structural steel, applications
where the point does not penetrate the steel member, or a
thickness of steel greater than 3/8", job site performance
tests are recommended.
Base Material Thickness
Steel base materials should be a
minimum of 1/8" in thickness.
edge Distance
for installations in A 36 steel, 1/2"
is the recommended minimum edge
distance.
Spacing
The recommended minimum distance
between fastenings is 1-1/2" center
to center for installations in ASTM A
36 steel.
Fastener length Selection in Steel
for permanent applications when using pins in steel, first
determine the thickness of the fixture to be fastened. To this,
add the thickness of the steel base material plus a minimum
of 1/4" to allow for proper point penetration. This will be the
minimum fastener shank length required. Do not select a
fastener length longer than that required for the application.
An excessively long shank can burnish or polish the hole
created in the steel resulting in a reduction in load capacity.
for removable applications with threaded studs, the
shank length required is equal to the thickness of the steel
base material plus a minimum of 1/4" to allow for proper
point penetration. This will be the minimum fastener shank
length required. Do not select a shank length longer than
that required for the application. An excessively long shank
can burnish or polish the hole created in the steel resulting
in a reduction in load capacity. To determine the minimum
threaded length, add the thickness of the fixture and the nut
/ washer thickness. The nut and washer thickness is equal to
the nominal thread diameter.
Do not over tighten threaded studs, the maximum
tightening torque is listed in the table below. Use of a nut
setter is recommended to reduce the possibility of over
tightening the fasteners. for critical applications, perform a
job site test.
P2201
POW2273_manual_P2201_dewalt.indd 4

Fastener Selection Guide

.300 head Diameter Drive Pins
CaT. Shank
no. lengTh
DDf3011000 1/2" k
DDf3011050 5/8" k
DDf3001100 3/4"
DDf3001150 1"
DDf3001200 1-1/8"
DDf3001250 1-1/4"
DDf3001300 1-1/2"
1/8" DDf3001350 1-3/4"
DDf3001400 2"
DDf3001450 2-1/4"
1/2"
DDf3001500 2-3/8"
DDf3001550 2-1/2"
DDf3001600 2-3/4"
DDf3001650 3"
1-1/2"
.300 head Diameter Drive Pins with Top hat
CaT. Shank
no. lengTh
DDf3031000 1/2" k
DDf3031050 5/8" k
DDf3031100 3/4"
DDf3031150 1"
.300 head Diameter Step Shank Pins
CaT. Shank
no. lengTh
DDf3041000 3/4" Step Shank 100
DDf3041050 1" Step Shank 100
.300 head Diameter Drive Pins - Master Pack
CaT. Shank
no. lengTh
DDf301100M 1/2" k
DDf301105M 5/8" k
DDf300110M 3/4"
DDf300115M 1"
DDf300125M 1-1/4"
DDf303100M 1/2" k TH
DDf303105M 5/8" k TH
DDf303110M 3/4" TH
DDf303115M 1" TH
.300 head Diameter Drive Pins with 3/4" Washer
CaT. Shank
no. lengTh
DDf3051100 3/4"
DDf3051200 2-1/2"
.300 head Diameter Drive Pins with 7/8" Washer
CaT. Shank
no. lengTh
DDf3061150 1"
DDf3061250 1-1/4"
DDf3061300 1-1/2"
DDf3061400 2"
DDf3061550 2-1/2"
DDf3061650 3"
.300 head Diameter Drive Pins with 1" Washer
CaT. Shank
no. lengTh
DDf3071000 1-1/4"
DDf3071050 1-1/2"
DDf3071250 2"
DDf3071150 2-1/2"
DDf3071200 3"
4
Cat. No. DDF211022P
STD. STD. heaD Shank
Box CTn. Dia. Dia.
100 5000 .300 .143
100 5000 .300 .143
100 5000 .300 .143
100 5000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
STD. STD. heaD Shank
Box CTn. Dia. Dia.
100 5000 .300 .143
100 5000 .300 .143
100 5000 .300 .143
100 5000 .300 .143
STD. STD. heaD Shank
Box CTn. Dia. Dia.
1000 .300 .143/130
1000 .300 .143/130
STD. STD. heaD Shank
Box CTn. Dia. Dia.
1000 5000 .300 .143
1000 5000 .300 .143
1000 5000 .300 .143
1000 5000 .300 .143
1000 5000 .300 .143
1000 5000 .300 .143
1000 5000 .300 .143
1000 5000 .300 .143
1000 5000 .300 .143
STD. STD. heaD Shank
Box CTn. Dia. Dia.
100 1000 .300 .143
100 1000 .300 .143
STD. STD. heaD Shank
Box CTn. Dia. Dia.
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
STD. STD. heaD Shank
Box CTn. Dia. Dia.
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
3/10/14 12:41 PM
WT./
100
.5
.5
.5
.6
.7
.8
.9
1.1
1.2
1.2
1.3
1.4
1.6
1.9
WT./
100
.5
.5
.5
.6
WT./
100
.5
.6
WT./
100
.5
.5
.5
.6
.8
.5
.5
.5
.6
WT./
100
1.6
2.5
WT./
100
1.9
2.0
2.1
2.4
2.7
3.0
WT./
100
2.2
2.3
2.6
2.9
3.2