Prior To Operating The Tool; 300 Head Diameter Drive Pins With; Preparation For Loading The Tool; Operating The Tool - DeWalt P2201 Operating Instructions Manual

Model P2201
.300 head Diameter Drive Pins with 1-7/8" insulation Washer
CaT. Shank STD.
no. lengTh Box CTn.
DDf3081000 1-1/2" 100
DDf3081050 2-1/2"
1/4"-20 Threaded Studs
CaT. ThReaD Shank STD.
no. lengTh lengTh Box
DDf3811020 1/2" 1/2"k
DDf3811000 3/4" 1/2"k
DDf3811050 3/4" 3/4"
DDf3811100 1/2" 1"
DDf3811150 3/4" 1"
DDf3811180 1/2" 1-1/4"
DDf3811200 3/4" 1-1/4"
DDf3811250 1-1/4" 1-1/4"
.300 head Diameter Pins with Ceiling Clips
CaT. Shank STD.
no. lengTh Box
DDf4111050 1" 100
DDf4151000 1" 100
DDf4111100 1-1/4" 100
DDf4111150 1-1/4" 100

.300 head Diameter Drive Pins with

Bx Cable Straps and Conduit Clips
CaT.
no. Shank lengTh
DDf4111150 1"
DDf4131050 1-1/4"
DDf4121000 1/2" EMT 1" pin
DDf4121050 3/4" EMT 1-1/4"pin
DDf4121100 3/4" EMT 1" pin TH
DDf4121150 3/4" EMT 1" pin
DDf4121200 1" EMT 1" pin TH
k=knurled TH=Top Hat
.300 head Diameter Pins with Rebar Basket Clip
CaT.
no. DeSCRiPTion
DDf4251000 32mm w/ basket clip 100
DDf4251050 37mm w/ basket clip 100
DDf4251150 37mm w/ basket clip 100
DDf4252000 37mm w/ basket clip 100
DDf4252500 37mm w/ basket clip 100
Forming Pins
CaT.
no. DeSCRiPTion
DDf3951050 62mm - 2-1/2"
DDf3951000 44mm - 1-5/8"
Powder Load Selection Guide
CaT. PoWeR loaD
no. level ColoR Size
DDf1111100 1 Grey
DDf1111200 2 brown
DDf1111300 3 Green
DDf1111400 4 Yellow
fety InstructIons
safety InstructIons
Safety is your primary responsibility when operating
any powder actuated tool. You must read and understand
P2201
POW2273_manual_P2201_dewalt.indd 5
STD. heaD Shank
Dia. Dia. 100
1000 .300 .143
50 500 .300 .143
STD. heaD Shank
CTn. Dia. Dia.
100 5000 1/4" .143
100 1000 1/4" .143
100 1000 1/4" .143
100 1000 1/4" .143
100 1000 1/4" .143
100 1000 1/4" .143
100 1000 1/4" .143
100 1000 1/4" .143
STD. heaD Shank WiRe
CTn. Dia. Dia. hole
1000 .300 .143 0.278"
1000 .300 .143 0.278"
1000 .300 .143 0.278"
1000 .300 .143 0.278"
STD. STD. heaD Shank
Box CTn. Dia. Dia.
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 500 .300 .143
100 1000 .300 .143
25 250 .300 143
STD. STD. heaD Shank
Box CTn. Dia. Dia.
100 8mm .143
100 8mm .143
100 8mm .143
100 8mm .143
100 8mm .143
STD. STD. heaD Shank
Box CTn. Dia. Dia.
100 1000 .205 .143
100 1000 .205 .143
STD. STD. MaSTeR WT./
Box CTn. CTn.
.22A 100 1000 20000
.22A 100 1000 20000
.22A 100 1000 20000
.22A 100 1000 20000
the contents of this manual. You must be familiar with all
functional and safety requirements of the tool. It is your
WT./
responsibility to obtain proper training and a D
2.1
card prior to using this tool in compliance with the current
2.7
American National Standard A10.3 Safety Requirements
for Powder Actuated fastening Systems and the federal
Occupational Safety and Health Administration Standards
(OSHA). Existing state or local regulations should also be
WT./
100
followed. when using this tool, you must have the qualified
.8
operators card in your possession.
1.1
Revocation of card - failure to comply with any of the rules and
1.2
regulations for safe operation of powder actuated tools shall be
1.2
cause for the immediate revocation of your qualified operator card.
1.4
Failure to following safety instructions
1.4
can result in serious injury or death to operators or
1.5
bystanders.
1.7

Prior to operating the Tool

1. warning signs should always be posted within the area in
WT./
which a powder actuated tool is to be used. These signs
100
3.5 should be at least 8" x 10" in size with boldface type that
3.0 is not less than 1" in height. The sign should state
3.7 "Powder Actuated Tool In Use".
3.2
2. Approved eye protection should always be worn by opera-
tor or bystander, to protect their eyes from flying particles.
Hearing protection should always be worn by the operator
and bystanders when using a powder actuated tool. Other
personal safety protection as required should also be used.
WT./
100
3. Never modify or fabricate parts for use in your D
3.5
tool. Use only D wALT fasteners, loads, and tool parts.
E
3.7
4. Hands or other body parts must never be placed in front
3.3
of muzzle/barrel. Accidental discharge can cause piston
3.5
and/or fastener to pass through the operator's hand.
3.4
5. Never compress the tool against any part of the body.
3.3
Serious injury or death may result in the event of an
3.2
accidental discharge.
6. Always point tool in a safe direction at all times.
intended Purpose
7. keep all other people, especially children, away from the
WT./
100
work area.
4.0
8. Use only in a well-lit, well-ventilated work area.
4.1
4.4

Preparation for loading the Tool

4.6
1. Tools must be checked prior to operating to make sure
4.8
they are not fully or partially loaded with a powder load or
fastener.
2. To insure safe operation, perform the daily function test
WT./
100
described in this manual. be sure the tool is not loaded
1.4
prior to performing this test.
1.2
3. Do not operate this tool unless all its parts are in place
and operating appropriately. Never attempt to use a
malfunctioning tool. Call 1-800-4-DeWalT for assistance.
4. Never guess about the suitability of a base material. If
you are uncertain about the suitability of a base material,
perform a center punch test.
100
5. Do not operate the tool until you learn and understand the
.33
.33 color code / numbering system used to identify the power
level of powder loads.
.33
.33

operating the Tool

1. Only use fasteners and powder loads designed for this
tool as supplied by D
E
2. Do not use powder actuated tools in the presence of
flammable fumes or vapor or an explosive atmosphere.
3. Do not fire a tool without a fastener. The piston will
5
Cat. No. DDF211022P
wALT operator
E
wALT
E
wALT.
3/10/14 12:41 PM