Memory Switch Setting Command; Esc Gs # M N N1 N2 N3 N4 Lf Nul - Star StarPRNT SM-L Series Command Specifications

2.3.19. Memory Switch Setting Command

ESC GS # m N n1 n2 n3 n4 LF NUL

[Name] Set memory switch
[Code] ASCII ESC GS
Hex. 1B
Decimal 27
[Defined Area] 48 ≤ n1 ≤ 57 ("0" ≤ n1 ≤ "9"), 65 ≤ n1 ≤ 70 ("A" ≤ n1 ≤ "F"), 97 ≤ n1 ≤ 102 ("a" ≤ n1 ≤ "f")
48 ≤ n2 ≤ 57 ("0" ≤ n2 ≤ "9"), 65 ≤ n2 ≤ 70 ("A" ≤ n2 ≤ "F"), 97 ≤ n2 ≤ 102 ("a" ≤ n2 ≤ "f")
48 ≤ n3 ≤ 57 ("0" ≤ n3 ≤ "9"), 65 ≤ n3 ≤ 70 ("A" ≤ n3 ≤ "F"), 97 ≤ n3 ≤ 102 ("a" ≤ n3 ≤ "f")
48 ≤ n4 ≤ 57 ("0" ≤ n4 ≤ "9"), 65 ≤ n4 ≤ 70 ("A" ≤ n4 ≤ "F"), 97 ≤ n4 ≤ 102 ("a" ≤ n4 ≤ "f")
m = 87, 84, 44, 43, 45, 64, 42 (m = "W", "T", ",", "+", "-", "@", "*"）
48 ≤ N ≤ 57 ("0" ≤ N ≤ "9"), 65 ≤ N ≤ (*)70 ("A" ≤ N ≤ (*)"F"), 97 ≤ N ≤ (*) 102, ("a" ≤ N ≤ (*) (*) "f")
N = 85 (N = "U") User defined area
(*) The memory switch defined area differs according to the model.
[Initial Value] - - -
[Function] Sends command to write after defining memory switch using the definition command specified by the
following classes.
Memory switch information defined by the command to write is written to the volatile memory.
When writing to the volatile memory by the command to write, the printer executes a reset.
You can load the default settings by specifying m = 42 (*).
You can register any 16 bit data by specifying N = 85 ("U").
(See the "Special Appendix, Command Table per Model" for details per model.)
Consider the life of the non-volatile memory and avoid excessive use of this command.
Definition data write and reset
Definition data write and reset and self print
Data definition (data specification)
Data definition (specify bit and set)
Data definition (specify bit and clear)
Definition data (all data initialized)
Definition data (load default settings)
• m:
• N:
• n1 n2 n3 n4:
[Model Limitations] SM-L200, SM-S, T Series : The function "load default settings" is not supported.
Star PRNT Command Specifications
# m N n1
1D 23 m N n1
29 35 m N n1
Functions
Mode selection
Memory switch number to specify
Specify data
n2 n3 n4 LF NUL
n2 n3 n4 0A 00
n2 n3 n4 10 0
Class
Write "W"
Write "T"
Definition ", "
Definition "+"
Definition
Definition "@"
Definition "*"
m = (",") Specify data
m = ("+") Bit number to set
m = ("-") Bit number to clear
2-82
m N n1 n2 n3 n4
Fixed at "0" Fixed at "0000"
Fixed at "0" Fixed at "0000"
N n1 n2 n3 n4
N n1 n2 n3 n4
"-" N n1 n2 n3 n4
Fixed at "0" Fixed at "0000"
Fixed at "0" Fixed at "0000"