Saf Ety - Seeley Breezair EXH Series Installation And Operating Instructions Manual

SAFETY INSTRUCTIONS
important Safety instructions and
Warnings
WARNING: The warnings and safety
instructions in this manual must be
followed to reduce the risk of fire,
electric shock or injury, and to provide
reasonable safety and efficiency in
using this Evaporative Air Cooler. The
operator is responsible for following
the warnings and instructions in this
manual and on the cooler.
Read this entire manual before
proceeding to install the cooler.
Restrict the use of this cooler to
persons who read, understand and
can follow the warnings and
instructions in this manual and on
the cooler. NEVER ALLOW
CHILDREN TO OPERATE THE
COOLER.
Failure to observe these warnings
and instructions will void
manufacturer's warranties and will
discharge the manufacturer of all
liability.
CAUTION!
ALWAYS disconnect the cooler
from the power supply before
commencing maintenance
procedures.
During maintenance procedures,
NEVER use a naked flame for any
inspection or cleaning purpose as a
fire could be caused by a flame
coming into contact with the cooler
materials.
Avoid Dangerous Situations:
Protect the cooler from all sources
of ignition because polymers and
cooling pads will burn.
NEVER use a water hose to squirt
the interior of the cooler for cleaning
as residual water could damage
electrical components and create the
risk of fire and/or electric shock to
the user after re-assembly.
INSTALLATION, REPAIR AND
OPERATION
• All installation and repair work
must conform to local electrical, water
supply and environmental codes,
rules and regulations and applicable
national standards.
• All installation, maintenance and
repair work must be done by a
licensed and qualified electrician
and/or a qualified, experienced
heating, ventilating, air
conditioning technician. All such
work must be effected with factory
authorized spare parts only.
• Disconnect electrical power at the
fuse or circuit breaker box before
installation commences. ALWAYS
turn OFF the isolating switch
(disconnect) located on the electronic
module inside the cooler BEFORE
commencing any maintenance
• Use only the power supply voltage
shown on the motor/cabinet
nameplate.
• Do not install or service the air
cooler during rain, high wind or severe
weather conditions.
• Keep children, bystanders and
animals at a safe distance, a minimum
of 30ft (10m) away from working
areas.
• Dress safely. Wear non-skid shoes
when working at high levels and roofs.
Do not wear loose clothing or personal
accessories while installing or
servicing the air cooler as they may
become caught in moving parts.
• Keep loose hair, loose clothing,
fingers and all other parts of the body
away from openings and moving
parts.
• Check the cooler for worn, loose,
missing, or damaged parts before
operation.
• If you work with power tools, wear
protective eyewear and gloves.
• Take care when lifting or raising the
air cooler to its final location. Use safe
equipment and never attempt to lift the
cooler alone. Always have assistance.
Otherwise you might damage the
cooler or the building or injure
yourself.
• Ground Fault Circuit Interrupter
(GFCI) protection should be provided
on the circuit supplying this air cooler.
Receptacles are available with built-in
GFCI protection.
• Air coolers installed on roofs must
not have the waste water directed
onto the roof as stains will occur.
Connect the cooler drain outlet to a
gutter or drain pipe using a suitable
hose.
• Always use the correct tools.
• WARNING! the packaging plastic
on this cooler can be a safety hazard.
Dispose of carefully.
• Never drill holes in the pan or walls
of the cooler.
• Avoid dangerous situations. Do not
use the cooler in the presence of
flammable liquids or gasses to avoid
creating fire or explosion. This air
cooler is NOT flame retardant. Afire
may result from contact with a flame
or from an electrical short.
• Use of wrong replacement parts
creates risk of severe electric shock
and fire which may result in serious
property damage, personal injury or
death.
WATER PUMP
The water pump is supplied with this
cooler and is factory fitted into its
correct location.
Ensure that it is properly secured and
upright as intended.
There is no need to adjust the water
flow since the cooler is designed to
operate with maximum cooling at low
air velocities.
Water pump replacement
Factory authorized pumps are fitted
with thermal overload protection.
Water pumps may seize up and
overheat, creating a fire risk. Pumps
that have thermal overload protection
are designed to shut off the pump if the
motor overheats.
Factory Authorized water pump
Seeley "Tornado" pump (part no.
095905)
"Power Clean" Style Timed Pumps
Under no circumstances are "Power
Clean" style timed pumps to be
used in any Breezair evaporative air
cooler. Use of these devices or any
other non-approved device will cause
serious damage to the special safety
circuits of this cooler. Failure to follow
this instruction will VOID ALL
WARRANTY and may create severe
risk of electric shock and fire!
FAN MOTOR
This cooler is supplied with a fan motor
made by the cooler manufacturer.
USE ONLYTHE AUTHORIZED FAN
MOTOR SUPPLIED.
Failure to follow this instruction will
VOID ALL WARRANTY and may
create severe risk of electric shock
and fire!
Factory Authorized Fan Motor
Seeley Direct Drive motors:
750W (1 HP) motor part# 095943
1500W (2HP) motor part # 095967
The fan motor is equipped with inbuilt
overheating protection that will reset
automatically on cool=down to a safe
temperature. This may take up to 45
minutes.
CIRCUIT BREAKER
PROTECTION
This cooler is fitted with circuit breaker
protection for the fan motor and pump.