Related Manuals for Ingersoll-Rand TS1401 Series
Summary of Contents for Ingersoll-Rand TS1401 Series
- Page 1 Form P7166 Edition 4 April 2007 CCN: 03540697 Turbine Powered Starters Series TS1401 Installation and Maintenance Information Save These Instructions...
- Page 2 Always wear eye protection when operating or performing maintenance on this starter. • Always wear hearing protection when operating this starter. • • Use only recommended Ingersoll Rand accessories. Safety Symbol Identification Wear Respiratory Wear Eye Wear Hearing Read Manuals Before...
- Page 3 Placing the Starter in Service (Dwg. TPA1470-1) 03540697_ed4...
- Page 4 Placing Starter in Service The Ingersoll Rand Starter is a precision piece of equipment 7. A leak in any of the connections is hazardous. Make your intended to give efficient, economical performance over a long connections right the first time to avoid unnecessary costs period of time, However, as with any product, performance, economy and delays.
- Page 5 13. Connect the Control Valve to the Relay Valve with 1/4“ hose. 15. Install a 1/4“ hose line from the “DEL” side of the Starter Control Install a Tee in this line with a short feeder hose to the Pressure Valve to the top of the Relay Valve.
- Page 6 Gear Assembly - Parts List (Dwg. TPA1473-2) ST999-A37 INT. GEAR CASE ASSEMBLY ST900-A108 PLANET GEAR FRAME ASSEMBLY Item Part No. Name Qty. Item Part No. Name Qty. SS800-22 Bearing ST900-108 Frame ST900-37 Gear Case T06-24 Bearing Y327-162 O-ring ST900-24 Bearing Y327-163 Seal ST900-191...
- Page 7 Motor Assembly - Parts List (Dwg. TPD1795) Item Part No. Name Qty. Item Part No. Name Qty. Shaft Seal Spacer Bearing Screw End Plate Pinion O-ring Spacer Washer End Plate O-ring Rotor Spring Spacer * These Parts Only Available as an Assembly. 03540697_ed4...
- Page 8 Series TS1401 Turbine Starter - Sectional View (Dwg. TPA1469) 03540697_ed4...
- Page 9 Series TS1401 Turbine Starter - Exploded View (Dwg. TPA1468-1) 03540697_ed4...
- Page 10 Series TS1401 Turbine Starter - Parts List Item Part Description Part Number Item Part Description Part Number Exhaust Kit ST700K-350 Carrier/Ring Gear 04324596 Directional Housing Exhaust Cover ST700-350 Bearing SS800-22 Exhaust Cover Seal Y330-257 Idler Gear Frame ST900-108 Exhaust Elbow Plug ROH-377 Idler Gear (3) ST900-10...
-
Page 11: Maintenance
This only should be Plugs (10) and drain the oil from the gearing before beginning done at an authorized Ingersoll Rand repair facility. disassembly of the Starter. 2. Using an 8 mm hex-head wrench, unscrew and remove the 6. - Page 12 9. Remove the Carrier/Ring Gear (17A). NOTICE 10. Remove Seal (16) and spacer (17). 11. Remove Bearing (17C) by pressing from front of Intermediate If the Idler Gear Frame will not come out of-the Motor Housing Gear Case. Refer to Dwg. TPD1743. easily, use a wooden dowel and tap the IdIer Gear Frame from inside the rear of the Motor Housing.
- Page 13 Assembly General Instructions 1. Always press on the inner ring of a ball-type bearing when installing the bearing on a shaft. 2. Always press on the outer ring of a ball-type bearing when pressing the bearing into a bearing recess. 3.
- Page 14 LOOSEN 1-1/2 TURNS ONLY. DO NOT REMOVE (Dwg. TPD1792) (Dwg. TPD1785) Assembly of the Directional Housing Exhaust Cover 12. Remove the Intermediate Gear Case from the vise and set it on a bench. 1. Coat the Exhaust Cover Seal (2) with O-ring lubricant and install in 13.
-
Page 15: Troubleshooting Guide
Operate according to recommendations. High number of start cycles Replace worn components. Tighten or replace Pipe plugs using Ingersoll Rand Loose or leaking Pipe Plugs (10) No. SMB-441 Pipe Sealant. Make sure that joints fit properly and Starter Assembly Cap Screws are tightened to 55 ft.-lb. - Page 16 TS1401 MAINTENANCE SCHEDULE Starts Components Recommendation C3 Turbine Oil Replace All External Cap Screws Check Torque Strainer Check Element 1000 C3 Turbine Oil Replace 1000 All External Cap Screws Check Torque 1000 Motor Assembly Replace 1000 All Bearings and Seals Replace 1000 Strainer...
- Page 17 Parts and Maintenance CAUTION The use of other than genuine Ingersoll Rand replacement parts may result in safety hazards, decreased motor performance, and increased maintenance, and may invalidate all warranties. Ingersoll Rand is not responsible for customer modification of motors for applications on which Ingersoll Rand was not consulted.
- Page 18 Notes:...
- Page 19 Notes:...
- Page 20 © 2007 Ingersoll Rand Company...
Need help?
Do you have a question about the TS1401 Series and is the answer not in the manual?
Questions and answers