Sony SRW-5000 Operation Manual page 80

C U E
R E C D A T E [ 2 0 0 3 / 0 2 / 2 5 ]
S C A N
T I T L E [ S O N Y
! D e l e t e C u e P o i n t :
N o . I N
E N T R Y
P O I N T
0 0 0 : 0 0 : 0 4 : 0 5
C U E
1 0 0 : 0 3 : 4 5 : 2 1 0 1 : 0 0 : 3 6 : 0 6 5 9 i 1 0 8 0
C O M M N T
2 0 1 : 0 4 : 2 7 : 2 3 0 1 : 0 5 : 3 1 : 2 4 5 9 i 1 0 8 0
E D I T P r e s s [ S F T ] + [ F 5 ] t o D E L E T E .
3 - - : - - : - - : - - - - : - - : - - : - - - - - - - - -
P r e s s o n l y [ C L R ] t o C A N C E L .
C H A N G E
D A T A
D E L M A R K
P O I N T
To undo the deletion of a time data or line
Press the ALT/[F2] (UNDO ALL) buttons.
A message appears (in the control panel display)
requesting confirmation of the undo operation.
Press the [F2] (UNDO ALL) button while holding
down the SFT button. To cancel the undo operation,
press the CLR button.
To copy time data of a cue point to another cue
point specified in the CUE menu
1
Press the ALT/[F4] (COPY to CUE) buttons.
A copy confirmation window appears.
To cancel the copy operation
Press the CLR button.
2
Press the [F4] (COPY to CUE) button while holding
down the SFT button.
The time data of the cue point is copied to the cue point
indicated in the CUE menu.
Changing Mrk data
Use the cursor buttons to move the cursor to the line with
the mark attribute to be changed, and then press the [F6]
(MARK) button. Or, move the cursor directly to the mark
attribute to be changed, and then press the [F4] (CHANGE
DATA) button. In both cases, each press of the button
changes the attribute as follows: OK t NG t KP
(KEEP) t blank (no attribute).
Changing the recording starting point setting
Use the cursor buttons to move the cursor to the recording
starting point section. Then press the [F4] (CHANGE
DATA) button. Each press of the button turns the setting
"on" (the @ indication appears) or "off" (the indication
disappears).
Entering and modifying IN/OUT point data
You can use either the ENTRY button or the numeric
buttons to enter and modify IN/OUT point data.
80
4-4 CUE Menu
E O S [ - - : - - : - - : - - ]
] R e s t 8 5 %
O U T T a p e F o r m a t
0 0 : 0 0 : 0 9 : 2 3 5 9 i 1 0 8 0
P R O - T A P E C U E N U M W R I T E /
T E C T I N F O P O I N T E X I T
To enter or modify IN/OUT point data using the
ENTRY button
1
Use the cursor buttons to move the cursor to the IN/
OUT section on which the current log data is to be
entered or modified.
To move the cursor using the numeric buttons
Enter the line number using the numeric buttons. Then
press the [F9] (CUENUM POINT) button. The cursor
will move to the line specified by the numeric buttons.
2
Press the IN button (to enter IN point data) or OUT
button (to enter OUT point data) while holding down
the ENTRY button.
The current time code is entered as the IN/OUT point
data or it replaces the existing IN/OUT point data.
Note
If the cursor is not on the IN/OUT section when pressing
the IN or OUT button while pressing down the ENTRY
button, the current cue point is entered or it replaces the
existing cue point. When pressing the ENTRY button only,
the cue point is entered or replaced regardless of the cursor
position.
To enter or modify IN/OUT point data using the
numeric buttons
3
1
Use the cursor buttons to move the cursor to the IN/
OUT section to be entered or modified.
2 1
2
1