Setup; Setting The Date And Time - Sony PDW-1500 Operation Manual

3-2 Setup

The principal setup operations before operating this unit
can be carried out using setup menus.
The setup menus of this unit comprise a basic setup menu
and an extended setup menu. The contents of these menus
are as follows.
Basic setup menu:
• Items relating to the hours meter
• Items relating to operation
• Items relating to menu banks
Extended setup menu:
• Items relating to control panels
• Items relating to the remote control interface
• Items relating to editing operations
• Items relating to preroll
• Items relating to disc protection
• Items relating to the time code, metadata, and UMID
• Items relating to video control
• Items relating to audio control
• Items relating to digital processing
For detailed information about the items, except for the
basic menu items relating to the hours meter, of these
menus and how to use them, see Chapter 8 "Menus." For
detailed information about menu operations relating to the
hours meter, see 9-1-1 "Digital Hours Meter" (page 113).
This unit allows three different sets of menu settings to be
saved in what are termed "menu banks" numbered 1 to 3.
Saved sets of menu settings can be recalled for use as
required.
For more information about the menu banks, see "Menu
bank operations (menu items B01 to B13)" (page 90).
42
3-2 Setup / 3-3 Setting the Date and Time
3-3 Setting the Date and
Time
When using this unit for the first time, you should set the
date and time as follows.
SG DATA SG DATA SG DATA SG DATA EDIT
ACCESS
ANA SDI ANA SDI ANA SDI ANA SDI INPUT
AE8/EBU AE8/EBU AE8/EBU AE8/EBU VITC VIUB
i.LINK
dB OVER dB OVER dB OVER dB OVER
0 0 0 0 SDI
CMPST
NETWORK -12 -12 -12 -12 Y-R,B
LOCAL -20 -20 -20 -20 SG
REMOTE
-30 -30 -30 -30 HOURS
MONITOR
-40 -40 -40 -40
MONITOR 1/2 3/4 AUDIO
-60 -60 -60 -60
CH- 15 CH- 26 CH- 37 CH- 48 5/6 7/8 4 8 CH
L
MIX
AUDIO VIDEO
R
MONITOR SEL METER SEL INPUT CH INPUT SEL INPUT SEL
ALL/CH-1 CH-2 CH-3 CH-4
VARIABLE
REC
PRESET
PB
PHONES
PREV PLAY NEXT STOP
F REV F FWD
TOP END
4
1
Holding down the SHIFT button, press the MENU
button.
The system menu appears on the monitor screen.
2
Select "DATE/TIME PRESET" using the F button or
f button, then press the g button.
The date and time setting screen appears on the
monitor, allowing you to set the following items.
• YEAR: Calendar year
• MONTH: Month
• DAY: Day
• TIME: Time
• TIME ZONE: Time zone (Difference from UTC)
3
Set the date, time and time zone.
You can change the setting of the flashing digits.
To change the flashing digits
Use the arrow buttons (G, g).
To increase or decrease the values of the flashing
digits
Use the arrow buttons (F, f) or jog dial.
4
Press the SET button.
The date, time and time zone settings are stored.
To return to the previous menu page
Press the MENU button.
To exit the menu
Press the MENU button twice in succession.
1
EJECT
REMOTE [9P iLINK] KEY INH
ALARM
COUNTER VITC REC INH
MINUTES SECONDS FRAMES
625 IMX[50 40 30]
18 24 BIT 525 DVCAM
COUNTER SYS MENU SHIFT
SELECT HOLD MENU
SUB THUMB
CLIP NAIL SET RESET
CLIP ESSENCE S.SEL
MENU MARK MARK1
REC
IN OUT
MARK2
2,3 3