Sony PDW-1500 Operation Manual page 90

SG DATA SG DATA SG DATA SG DATA
ACCESS
ANA SDI ANA SDI ANA SDI ANA SDI
AE8/EBU AE8/EBU AE8/EBU AE8/EBU
dB OVER dB OVER dB OVER dB OVER
0 0 0 0
NETWORK
-12 -12 -12 -12
LOCAL -20 -20 -20 -20
REMOTE
-30 -30 -30 -30
-40 -40 -40 -40
MONITOR
-60 -60 -60 -60
CH- 15 CH- 26 CH- 37 CH- 48
L
MIX
AUDIO
R
MONITOR SEL METER SEL INPUT CH INPUT SEL
ALL/CH-1 CH-2
VARIABLE
REC
PRESET
PB
PHONES
PREV PLAY NEXT
TOP F REV F FWD
1
Press the MENU button.
The menu appears in the time data display.
2
Press the RESET button.
A message "Init setup?" appears in the time data
display.
To abandon operations and return to the setup
menu display
Press the RESET button again.
3
Press the SET button.
The menu settings are reset to their factory default
settings.
Switching between 525(U)-line, 525(J)-line
and 625-line modes (menu item 013)
To switch between 525(U)-line, 525(J)-line and 625-line
operation modes, do as follows.
1
Press the MENU button.
2
Turn the jog dial or shuttle dial to display menu item
013 in the time data display.
3
Hold down the SHUTTLE button, and turn the jog dial
or shuttle dial to set menu item 013 to "on."
4
Press the SET button.
5
Hold down the SHUTTLE button, and turn the jog dial
or shuttle dial to select the line mode 525(U), 525(J) or
625.
6
Press the SET button.
90
8-2 Basic Setup Menu
1 2
EJECT
EDIT REMOTE [9P iLINK] KEY INH
ALARM
INPUT
VITC VIUB COUNTER VITC REC INH
i.LINK
SDI
CMPST
Y-R,B
SG
HOURS MINUTES SECONDS FRAMES
MONITOR
1/2 3/4 AUDIO 625 IMX[50 40 30]
5/6 7/8 4 8 CH 18 24 BIT 525 DVCAM
VIDEO COUNTER SYS MENU SHIFT
INPUT SEL SELECT HOLD MENU
SUB THUMB
CH-3 CH-4
CLIP NAIL SET RESET
CLIP ESSENCE S.SEL
MENU MARK MARK1
STOP REC
IN OUT
END
MARK2
3
7
Turn the unit off (press the on/standby switch to put
the unit in the standby state).
Next time the unit is turned on (when the unit is put in the
operating state by pressing the on/standby switch), it
operates in the new mode.
Menu bank operations (menu items B01 to
B13)
This unit allows menu settings to be saved in what are
termed "menu banks." Saved sets of menu settings can be
recalled for use as required.
To jump to menu item B01
You can recall any required menu by turning the jog dial
or shuttle dial after pressing the MENU button.
If you press the MENU button first, then the COUNTER
SELECT button, you can jump directly to menu item B01
or H01. The recalled menu item toggles between B01 and
H01 every time you press the COUNTER SELECT button.
Saving the current active menu settings
Set one of menu items B11 "SAVE SETUP BANK-1" to
B13 "SAVE SETUP BANK-3" to "on," depending on
which of the menu banks you wish to save in, then press
the SET button.
Recalling settings from a menu bank
Set one of menu items B01 "RECALL SETUP BANK-1"
to B03 "RECALL SETUP BANK-3" to "on," depending
on which of the menu banks you wish to recall from, then
press the SET button.
Recall
Current active
menu settings
Save
Recall
Save
Recall
Save
Menu bank 1
Menu bank 2
Menu bank 3