Sony PDW-1500 Operation Manual page 51

Indicators above the time
data display
SG DATA SG DATA SG DATA SG DATA EDIT REMOTE [9P iLINK]
ACCESS
ANA SDI ANA SDI ANA SDI ANA SDI INPUT
VITC VIUB COUNTER
AE8/EBU AE8/EBU AE8/EBU AE8/EBU i.LINK
dB dB dB dB
OVER OVER OVER OVER
0 0 0 0 SDI
CMPST
NETWORK -12 -12 -12 -12 Y-R,B
LOCAL -20 -20 -20 -20 SG
REMOTE -30 -30 -30 -30 HOURS MINUTES
-40 -40 -40 -40 MONITOR
MONITOR
-60 -60 -60 -60 1/2 3/4 AUDIO
CH- 15 CH- 26 CH- 37 CH- 48 5/6 7/8 4 8 CH 18 24 BIT
L
MIX
R AUDIO VIDEO COUNTER
MONITOR SEL METER SEL INPUT CH INPUT SEL INPUT SEL SELECT
ALL/CH-1 CH-2 CH-3 CH-4
VARIABLE
REC
PRESET
PB
PHONES NEXT
PREV PLAY STOP REC
TOP F REV F FWD END
1
1
Watching the indicators above the time data display,
press the COUNTER SELECT button to select TC.
2
Press the HOLD button.
The SHUTTLE button lights and the first two digits of
the time code shown in the time data display start
flashing.
To set all digits to 0
Press the RESET button.
3
Select the digits to set by rotating the shuttle dial or jog
dial.
The flashing digits change to the next two digits on the
right when you rotate the shuttle dial or jog dial
clockwise, and to the next two digits on the left when
you rotate it counterclockwise.
4
Set the value for the flashing digits by rotating the
shuttle dial or jog dial while holding the SHUTTLE
button.
5
Repeat steps 3 and 4 until you finish setting all digits.
6
Press the SET button.
• An initial time code value is set and the monitor
returns to the time code display before the HOLD
button was pressed in step 2.
• If extended menu item 627 "RUN MODE" is set to
"free run," the time code starts advancing from the
initial value immediately.
Time data display
SHUTTLE button
4
3,4
EJECT
KEY INH ALARM
VITC REC INH
SECONDS FRAMES
625 IMX[50 40 30]
525 DVCAM
SYS MENU SHIFT
HOLD MENU
SUB THUMB
CLIP NAIL SET RESET
CLIP ESSENCE S.SEL
MARK1
MENU MARK
IN OUT
MARK2
RESET button
2 6
To set time code to the current time
With extended menu item 627 "RUN MODE" set to "free
run" and 628 "DF MODE" to "on (df)," do as follows.
For details of the extended menu operations, see 8-3-2
"Extended Menu Operations" on page 102.
1
Carry out steps 1 to 5 of the previous section "To set
an initial value" to set the time code to a time slightly
ahead of the current time.
2
Press the SET button at the instant when the current
time matches the displayed time code.
To set user bits
You can record up to eight hexadecimal digits of
information (date, time, clip number, etc.) in the time code
track.
Do as follows.
Indicators above the time
data display
SG DATA SG DATA SG DATA SG DATA
EDIT
ACCESS ANA SDI ANA SDI ANA SDI ANA SDI
INPUT
AE8/EBU AE8/EBU AE8/EBU AE8/EBU VITC VIUB
i.LINK
dB dB dB dB
OVER OVER OVER OVER
0 0 0 0 SDI
CMPST
NETWORK -12 -12 -12 -12 Y-R,B
LOCAL -20 -20 -20 -20 SG
REMOTE -30 -30 -30 -30 HOURS
-40 -40 -40 -40 MONITOR
MONITOR
-60 -60 -60 -60 1/2 3/4 AUDIO
CH- 15 CH- 26 CH- 37 CH- 48 5/6 7/8 4 8 CH
L
MIX
R AUDIO VIDEO
MONITOR SEL METER SEL INPUT CH INPUT SEL INPUT SEL
ALL/CH-1 CH-2 CH-3 CH-4
VARIABLE
REC
PRESET
PB
PHONES
PREV PLAY NEXT
STOP
F REV F FWD
TOP END
1
Watching the indicators above the time data display,
press the COUNTER SELECT button to select UB.
2
Carry out steps 2 to 6 of the section "To set an initial
value" (page 50).
Settings are made in hexadecimal (0, 1, 2,... 8, 9, A,
B,... E, F).
To record time code that follows
sequentially upon the last recorded time
code
You can record time code so that it is continuous from one
clip to the next on the disc.
Set extended menu item 626 "TC MODE" to "int regen"
beforehand. When this setting is in force, the unit reads the
time code of the last frame of the last recorded clip on the
disc before starting to record, and internally generates time
code that follows upon the recorded time code.
EJECT
REMOTE [9P iLINK]
KEY INH ALARM
COUNTER VITC REC INH
MINUTES SECONDS FRAMES
625 IMX[50 40 30]
18 24 BIT 525 DVCAM
SHIFT
COUNTER SYS MENU
SELECT HOLD MENU
SUB THUMB
CLIP NAIL SET RESET
CLIP ESSENCE S.SEL
MARK1
MENU MARK
REC
IN OUT
MARK2
1
4-1 Recording
51