INTENDED USE device. All Vallox ventilation units have been designed to provide appropriate and continuous ventilation so as to present no threat to health and to maintain structures in good condition. IMPORTANT...
INSTALLATION OPTIONS • Vallox 101 MV can be mounted either on the wall, or on the ceiling by using a mounting plate (optional). NOTE The standard equipment and available accessories vary from country to country.
At the same time you create a MyVallox Cloud account for yourself. Read more about the service at www.myvallox.com. Ventilation unit control options. Operation of the Vallox ventilation unit can be controlled by the following means: • Through the control panel installed in the building •...
MAIN PARTS R model in the figure Extract air fan Post-heating radiator (in the supply air duct) Supply air fan Safety switch Supply air filter F7 Control panel Heat recovery cell Carbon dioxide sensor Bypass flap Humidity sensor Supply air filter G4 Internal humidity sensor Extract air filter G4...
Make sure that the unit is horizontally level after mounting. MOUNTING ON THE CEILING Vallox 101 MV can be equipped with an optional ceiling mount plate. To attach the ceiling mounting plate: • On rafter frames or other frame structure with M8 thread bars so that they withstand the weight of the unit.
Installing the ventilation unit to the ceiling mounting plate Install the ceiling mounting plate with M8 thread bars so that it is horizontally level. NOTE The end of the thread bars must be 5 mm or less below the fastening nut. Do not fasten the ceiling mounting plate too tight to the ceiling.
WATER SEAL NOTE The Vallox Silent Klick water seal package is delivered with the unit. Installation instructions for the water seal are enclosed with the packaging, and can also be found online at www.vallox.com. When the alternative water seal installation method is used, the ring seal and the locking part must be moved to the pipe connection part that is mounted on the wall.
DIMENSIONS AND DUCT OUTLETS Main parts Dimensions and duct outlets Dimensions R model in the figure. 461,50 In the L model, the parts are mirrored 136,50 1. Extract air fan 7. Supply air filter G4 8. Extract air filter G4 2.
To replace the filters: Disconnect the ventilation unit from the mains electricity supply. 2. Open door of the Vallox ventilation unit by undoing the finger screws. 3. Lift the door off. 4. Remove the old filters (A, B, C) and discard them.
Disconnect the ventilation unit from the mains electricity Handle the cell supply. carefully! For example, 2. Open door of the Vallox ventilation unit by undoing the do not lift the cell by the finger screws. layers. The cell layers are very thin and easily 3.
To clean the fan: Handle the fan blades Disconnect the ventilation unit from the mains electricity supply. carefully. Do not 2. Open door of the Vallox ventilation unit by undoing the finger remove or move the screws. fan blade balancing 3.
EXTERNAL ELECTRICAL CONNECTION 7028350 2014-08-29 JS MyVallox MyVallox Control REMOTE 0.3W MONITORING transmitter Modbus RTU 2x2x0,5+0,5 2x2x0,5+0,5 MyVallox MyVallox 2x2x0,5+0,5 Control transmitter 1.2W 2x2x0,5+0,5 2x2x0,5+0,5 External temperature Analog input sensor two different 2x0,5 2x0,5 NTC 4K7 functions 2x0,5 2x0,5 2x0,5 Potential-free contact data 24VDC can be programmed to display...
NOTE: COOLING ventilation unit. In this case, the pump and the solenoid valve can be controlled using a Vallox MV ventilation unit, The value set for the and no separate thermostats are needed.
Damper motor 930621 attenuation grid MyVallox Control control Wall mounting plate 3080700 Post-heating resistor 942220 949033 panel Water seal Vallox Silent MyVallox humidity sensor 3292500 Door 4102334 946149 Klick (optional) MyVallox carbon dioxide Mounting screw of the Filter (F7+G4, supply)