Virtual Concatenation Delay Generation; Event Triggers Outputs - Otn/Sonet/Sdh; Trigger Output Port For Otn/Sonet/Sdh - Agilent Technologies OmniBER OTN J7232A Technical Data Sheet

Virtual Concatenation Delay Generation

Up to 256ms can be added to any or all members of the
Delay
virtual concatenated. Full delay generation to ITU-T
Generation
G.707.
Delay can be entered in microseconds to 2 decimal
Delay Control
places with On/Off control provided. Also for each
member selected it is possible to increment/
decrement the pointer to hitlessly vary delay.

Event triggers outputs - OTN/SONET/SDH

Source: LOS - available with alarm stress 'Pulse'
OTN transmit
mode
triggers
OTU2: LOF, OOF, LOM, OOM, AIS, IAE, BDI,
ODU2: AIS, OCI, LCK, BDI,
Format: Level
Source: Start of frame, entire frame error add, frame
error (OA1,OA2), MFAS
OTU2: BIP8, BEI
ODU2: SM BIP8, SM BEI, FEC Block error, bit
Format: Pulse
Source:
OTN receive
OTU2: LOF, OOF, AIS, IAE, BDI
triggers
ODU2: AIS, OCI, LCK, BDI
Format: Level
Source: Start of frame, frame error (OA1,OA2), MFAS
OTU2: BIP8, BEI
ODU2: BIP8, BEI
FEC Block error
Format: Pulse
Note: All of the above triggers are selectable for frame
capture
Alarms
SONET
Physical: LOS
transmit
Transport O/H: LOF, SEF, AIS-L, RDI-L
triggers
Path O/H: AIS-P, AIS-C, LOP-P, LOP-C, RDI-P,
UNEQ-P,
Virtual Concatenation: OOM1, OOM2, LOM, SQM
Format: Level
Errors/Events
Transport O/H: Start of frame, entire frame error add,
frame error (A1,A2), CV-S(B1), CV-L(B2), REI-L
(CV-LFE)
Path O/H: CV-P(B3), REI-P (CV-PFE)
Payload: Bit
Format: Pulse
Alarms
SONET receive
Physical: LOS
triggers
Transport O/H: LOF, SEF, AIS-L, RDI-L, K1/K2 change
Path O/H: LOP-P*, LOP-C*, AIS-P*, AIS-C*, RDI-P,
UNEQ-P
Virtual Concatenation: OOM1, OOM2, LOM, LOA,
SQM
Format: Level
Errors/Events
Transport O/H: Start of frame, frame error, CV-S(B1),
CV-L(B2), REI-L(CV-LFE), STS pointer change
Path O/H: CV-P(B3), REI-P (CV-PFE)
Format: Pulse
Note: TOH event triggers are selectable for TOH frame
capture.
STS event triggers are selectable for STS-Path
capture.
* Trigger not available for Entire Overhead Capture
OmniBER OTN Communications Performance Analyzers
Alarms
SDH transmit
Physical: LOS
triggers
Section O/H: LOF, OOF, MS-AIS, MS-RDI,
Path O/H: AU-AIS, AU-AIS-C, AU-LOP, AU-LOP-C,
HP-RDI, HP-UNEQ
Tandem path: TC-OOM, VC-AIS, TC-IAIS, TC-RDI, ODI,
TC-UNEQ
Virtual Concatenation: OOM1, OOM2, LOM, SQM
Format: Level
Errors/Events
Section O/H: Start of frame, entire frame error add,
frame error (A1,A2), B1 BIP, B2 BIP, MS-REI
Path O/H: B3 BIP, HP-REI
Tandem Path: IEC, TC-REI, OEI
Payload: bit
Format: Pulse
Alarms
SDH receive
Physical: LOS
triggers
Section O/H: LOF, OOF, MS-AIS, MS-RDI, K1/K2
change
Path O/H: AU-AIS*, AU-AIS-C*, AU-LOP*, AU-LOP-C*,
HP-RDI, HP-UNEQ
Tandem Path: TC-OOM, VC-AIS, TC-IAIS, TC-RDI, ODI,
TC-UNEQ
Virtual Concatenation: OOM1, OOM2, LOM, LOA,
SQM
Format: Level
Errors/Events
Section O/H: Start of frame, frame error (A1,A2), B1
BIP, B2 BIP, MS-REI, , AU-3/4 pointer change
Path O/H: B3 BIP, HP-REI
Tandem Path: IEC, TC-REI, OEI, TC-ERR
Format: Pulse
Note: RSOH and MSOH event triggers are selectable
for RSOH+MSOH frame capture.
POH event triggers are selectable for POH capture.
* Trigger not available for Entire Overhead Capture

Trigger output port for OTN/SONET/SDH

SMA, TTL, 50ohm
Connectors
Logic '1' = 4V typical
Output level
Logic '0' = 0V typical
100ns Nominal
Pulse Width
19