Advertisement
Quick Links
Product
Modore 75H
Information
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed
for the protection of children and other at-risk individuals.
Une barrière conçu pour réduire le risque de brûlure par le verre de visualisation chaude est fournie avec cet appareil et doit
être installé pour la protection des enfants et autres personnes à risque.
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could
result in serious injury, death, or property damage.
- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Leave the building immediately.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call
the fire department.
- Installation and service must be performed
by a qualified installer, service agency or the
gas supplier.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
Element4 Gas Fireplaces Rev# 08222019
Video
Installation, Operation and
Owner's Manual
Modore 75H
Direct Vent
Gas Fireplaces
Une surface vitrée chaude
peut causer des brûlures.
Laisser refroidir la surface
vitrée avant d'y toucher.
Ne permettez jamais á un enfant
de toucher la surface vitrée.
AVERTISSEMENT:
INCENDIE OU D'EXPLOSION
Le non-respect des avertissements de sécurité à la
lettre pourrait entraîner de graves blessures , la mort
ou des dommages matériels.
- Ne pas entreposer ni utilizer d'essence ni d'autres vapeurs
ou liquides inflammables dans le voisinage de cet appareil
ou de tout autre appareil.
- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ
• Ne pas tenter d'allumer d'appareil.
• Ne touchez á aucan interrupteur. Ne pas vous servir des
téléphones se trouvant dans le bátiment ou vous trouvez.
• Quitter immédiatement le bâtiment.
• Appelez immédiatment votre fournisseur de gaz depuis
un voisin. Suivez les instructions du fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de gaz
appelez le service des incindies.
- Installation et l'entretien doivent être effectués par un
installateur qualifié, une agence de service ou le fournisseur
de gaz.
INSTALLATEUR: Laissez cette notice avec l'appareil.
CONSOMMATEUR: Conservez cette notice pour
consultation ultérieure.
1
4006611
August 2019
EuropeanHome.com
Advertisement
Related Manuals for Element4 Modore 75H
Summary of Contents for Element4 Modore 75H
- Page 1 INSTALLER: Leave this manual with the appliance. INSTALLATEUR: Laissez cette notice avec l’appareil. CONSUMER: Retain this manual for future reference. CONSOMMATEUR: Conservez cette notice pour consultation ultérieure. August 2019 Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com 4006611...
-
Page 2: Table Of Contents
Replacement Parts ........................48 Warranty ............................49 Massachusetts Certification................Appendix One Troubleshooting Flowchart ................Appendix Two Installing the Optional Wall Switch ............Appendix Three Connecting To A Smart Home System ............Appendix Four Index .............................. 58 Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com... -
Page 3: Important Safety Information
36” of the fireplace glass. SAVE THESE INSTRUCTIONS Make yourself fully aware of all the following instructions and the many features of the Element4 direct vent gas fireplace appliance. INSTALLER: Leave this manual with the appliance. OWNER: Keep this manual for future reference. - Page 4 Canada, consult with the local authority having The glass must only be removed by a qualified person. jurisdiction for gas product installations to determine their Gloves should be worn when removing the glass. specific requirements for high altitude installations. Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
- Page 5 1/16” when converted. If greater accuracy is DO NOT USE abrasive cleaners on the panels. DO NOT required, use the metric dimensions. ATTEMPT to clean the glass panels when they are hot. Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
-
Page 6: Key Installation Points
Gas pressures MUST be read with a manometer and confirmed with what is required in the installation manual. • FINISHING A 1/8”/3 mm gap between the flange and the enclosing wallboard MUST be maintained to prevent cracking • from heat expansion and contraction. Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com... -
Page 7: User Information
WARMTH AND BEAUTY - HOW IT WORKS The Element4 fireplaces are direct vent fireplaces and, as such, the intake and exhaust are both handled through the vent pipe. The fireplace also provides convection air to your room. The illustration shows one of the unique features of the Element4 fireplaces - its use of warm, convection air flow. -
Page 8: Specifications And Dimensions
New Efficiency A sample listing label image is shown Figure 2 above. A metal listing label is attached to every Element4 fireplace and contains important certification information. The listing label must not be removed from the fireplace. AC ADAPTER SPECIFICATIONS... -
Page 9: Modore 75H
Modore 75H Cut Sheet Element4 B.V. EuropeanHome SPECIFICATIONS and DIMENSIONS MODORE 75H 08/2017 Figure 7 MODORE 75H This information is for reference only. Please consult the Installation Manual for all details prior to making any design decisions. -
Page 10: Parts Of The Fireplace
SPECIFICATIONS and DIMENSIONS PARTS OF THE FIREPLACE The various parts of the Modore 75H fireplace are shown in Figures 8 thru 11. These parts are typical of any Element4 fireplace. Relief Doors (hidden) Figure 8 The “No Material Zone” and the “Top of Fireplace” is the same for both sides of the fireplace. - Page 11 Vent Collar - accepts the 5” x 8” venting adapter (included) Relief Door - part of the safety system. Do NOT block the operation. Check BEFORE 1st light. Pilot Assembly Side Trim - (2) Flange Figure 11 Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
-
Page 12: Clearances
VALVE, ELECTRICAL WIRING, AND GAS LINES) DOES NOT IMPEDE THE FULL OPERATION OF THE RELIEF DOORS. IT IS YOUR RESPONSIBILITY TO ENSURE THE SAFETY OF THESE CRITICAL COMPONENTS THROUGHOUT THE INSTALLATION PROCESS. REMOVE AND DISPOSE OF ALL WRAPS AND TIES. Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com... -
Page 13: Clearances To Combustibles
We recommend that the fireplace be set into its final location before building the enclosure. Please refer to the “Reduced Clearance to Existing Combustible Wall” section for use of combustibles inside of the above clearances. Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com... -
Page 14: Mantel Clearances
(TYPICAL) Mantel Depth NON COMBUSTIBLE 12”/300 mm MATERIAL CONSTRUCTION BEAMS NON- COMBUSTIBLE (TYPICAL) DETAIL C ETAIL C 1”/25 mm ALE 1 : 10 TOP OF FIREPLACE OPENING GLASS Figure 15 Figure 16 CONVECTION GAP Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com... -
Page 15: Convection Clearances
Minimum Distances Convection Air Outlet Area by Model Room ceiling to 72” Model Square Inches Square Centimeters appliance bottom 1830 Modore 75H Room ceiling to top of 1” Convection Air Outlet Figure 19 Figure 18 Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com... -
Page 16: Gas And Electric
Remove batteries after use to avoid battery corrosion. Battery corrosion will damage the receiver. Electrical work must be performed by a qualified, licensed electrician. WARNING All wiring shall be in compliance with all local, city, and state codes. Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com... -
Page 17: Venting
Pro-Form (BDM - Bernard Dalsin Manufacturing) Direct-Temp (Selkirk Corporation) AmeriVent Direct Vent (Hart & Cooley Inc.) Ventis Direct Vent (Olympia Chimney Supply, Inc.) Figure 21 Please visit www.europeanhome.com/technical-support/ for the power venting installation manuals Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com... - Page 18 Calculate the Total Vertical Section by adding up all vertical upward sections in your specific vent design. CALCULATING THE TOTAL HORIZONTAL SECTION (THS) Calculate the Total Horizontal Section by adding up all horizontal sections in your specific vent design. Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
- Page 19 Do not modify the restrictor(s). Please use the graph above (Figure 26) to determine if you will need to use a restrictor. Loosen these two Phillips head screws to slide the restrictor on/off. Figure 27 Figure 28 Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
-
Page 20: Venting Charts
VENTING VENTING CHARTS HORIZONTAL TERMINATIONS & RESTRICTOR USE rise Figure 29 VERTICAL TERMINATIONS & RESTRICTOR USE rise Figure 30 Figure 31 Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com... - Page 21 VENTING CLEARANCES HORIZONTAL VENT TERMINATION CLEARANCES AND REQUIREMENTS Figure 32 Figure 33 Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
- Page 22 National Fuel Gas Code (ANSI Z223.1 in the USA) or the current standard of CAN/CSA-B149.1 in Canada. Figure 34 Figure 35: Termination Heights A second termination may be no closer than 12”/305 Figure 36: Multiple Termination Clearance Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
-
Page 23: Enclosing The Fireplace
Figure 37: * The listed brand names are trademarks of their respective companies. Skamol Americas, Inc. (844) 475-2665 E-mail: skamotec225@skamol.com www.skamotec225.com Promat Inc. (865) 681-0155 E-mail: sales@promat.us www.promat.us/en James Hardie Building Products (888) 542-7343 www.jameshardie.com Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com... -
Page 24: Building The Enclosure
ENCLOSING the FIREPLACE BUILDING THE ENCLOSURE/FRAMING A safe installation of your Element4 fireplace requires that three things be clearly understood. 1. Most important, these fireplaces are NOT zero-clearance fireplaces. Unlike zero-clearance fireplaces, there is not an outer metal box around the Element4 fireplaces which increases the framing dimensions. - Page 25 OMbuSTIbLE hIELd INIShEd OMbuSTIbLE hIELd INIShEd Figure 39 2”/50 Minimum Air Gap MUST BE MAINTAINED 1”/25 Minimum Air Gap MUST BE MAINTAINED Figure 38 OMbuSTIbLE hIELd INIShEd hIELd INIShEd OMbuSTIbLE Figure 40 Figure 41 Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
- Page 26 When enclosing the Modore 75H fireplace there is a minimum clear area which must be maintained. Nothing except the Modore 75H may be within this area. When enclosed, the Modore 75H is flush with the front wall - stand off frame face in line with the front inside or back inside blue limit- above.
- Page 27 James Hardie Building Products HardieBacker® 500 1/2” Cement Board 1/2” (12 James Hardie Building Products HardieBacker® 1/4” Cement Board 1/4” (6 Figure 43 Fireplace Trim Figure 45 Minimum Wall Thickness = 1/2”/12 Figure 44 Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
-
Page 28: Convection Air Opening
Shown here are a number of ways to design the convection air outlet into your project (Figures 46 and 47). Modore 75H with Air Outlets in Wall... - Page 29 Figure 49 Use the adjustable feet to ensure that the fireplace is level prior to enclosing it. Do NOT lift the fireplace by the face frame but by the bottom of the cabinet. Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
-
Page 30: Cold Climate Installation
When measured at the level of the feet, the controls will reach no farther from 31” 31” the cabinet edge than shown at left (Figure 50). The drawing is not to scale. 40” 1060 Figure 50 Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com Front Elevation R Elevation... - Page 31 Replace the white door/frame cover onto the frame and secure it with the four bolts. Figure 53 Figure 54 Fit the gas control tab into the bracket on Tighten the bolt through the mounting the Access Door frame. bosses. Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
- Page 32 45 minutes to ensure the system works properly when heated. DO NOT OPERATE THE BURNERS WITH THE GLASS OFF FOR MORE THAN THREE (3) MINUTES OR DAMAGE WILL OCCUR! Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
-
Page 33: Installing The Fire Media
- one small bag of ash (optional use) - two pine cones - nine logs - two bags of black and two bags of grey chips Figure 57 Figure 58 Figure 59 Figure 60 Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com... - Page 34 C shows the 2 thermocouple area (Figure 62) clear of media (Figure 61). 2nd Thermocouple Pilot Assembly Figure 62 To see how to arrange media in an Element4 fireplace please visit the link below. WWW.EUROPEANHOME.COM/RESOURCES/VIDEOS/ Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
-
Page 35: Screen Installation
Place the two Lower Tabs on the trim, with the short side against the glass, about 2-3” from each corner of the glass. Place a magnet on the front of each tab. Figure 68 Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com... - Page 36 Figure 70 This is what the screen will look like (Figure 69) when it is attached correctly to the top Upper Tabs (viewed from inside of the standoff frame). Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
- Page 37 This is what the screen will look like (Figure 71) when it is attached correctly to the Lower Tabs (viewed between the screen and the glass). Figure 72 The screen is installed properly (Figure 72). Ensure that all magnets are in the correct position and the tabs are secured. Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
-
Page 38: Operating The Fireplace
Figure 74 Note! For normal operation the MANUAL knob on the gas valve cannot be in the MAN position; it must be fully in the ON position. Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com... - Page 39 OPERATING the FIREPLACE OPERATING the FIREPLACE 10 BUTTON REMOTE CONTROL Multi-Burner Status Figure 75 Figure 77 Figure 76 Figure 78 Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com Element4 Gas Fireplaces EuropeanHome.com Element4 Gas Fireplaces IGE4-2301-181107...
- Page 40 Figure 79 Figure 80 Figure 81 Figure 82 Figure 83 NOTE: There is a 2 min delay before the next ignition is possible. Figure 85 Figure 84 Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com Element4 Gas Fireplaces IGE4-2301-181107 Element4 Gas Fireplaces EuropeanHome.com...
- Page 41 OPERATING the FIREPLACE OPERATING the FIREPLACE OPERATING the FIREPLACE Figure 86 Figure 87 Figure 89 Figure 88 Figure 90 Figure 92 Figure 91 Figure 94 Figure 93 Element4 Gas Fireplaces Element4 Gas Fireplaces EuropeanHome.com IGE4-2301-181107 Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
- Page 42 LED Mode can only be used for Club and Summum Series replaces. Press the button to turn on, dim, and turn o LED burner function. To change LED color (Club Series only) you must use the ProControl App. Element4 Gas Fireplaces IGE4-2301-181107 Element4 Gas Fireplaces EuropeanHome.com Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
- Page 43 • CHILD PROOF (To activate press buttons simultaneously. displayed and the handset is rendered inoperable (except for off functi- on). • PROGRAM MODE • THERMOSTATIC MODE (also deactivates Program Mode) • ECO MODE • MULTI-BURNER FEATURE • COUNTDOWN TIMER Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
- Page 44 Since it is a metal fireplace, the heat-up and cool-down cycles may produce some noises caused by the expansion and contraction of these metals. The premium materials and build quality of your fireplace will keep these sounds to a minimum. Figure 100 To see an Element4 fireplace starting and running normally please visit the link below. WWW.EUROPEANHOME.COM/RESOURCES/VIDEOS/ Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
-
Page 45: Maintenance
PANEL(S) BEFORE LIGHTING THE FIRE! Figure 103 Remove the ROPE GASKET starting from one end down to the other end To see how to remove the glass from an Element4 fireplace please visit the link below. WWW.EUROPEANHOME.COM/RESOURCES/VIDEOS/ Figure 104 The ROPE GASKET will be... - Page 46 Step 4. While ensuring that the glass panels are tight and square to each another, carefully install the remaining rope gaskets. PROPERLY PLACE ROPE GASKET(S) AND SEAL THE GLASS PANEL(S) BEFORE LIGHTING THE FIRE! Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
-
Page 47: Burner
The pilot has two distinct flames, one engulfing the thermocouple on its left, the other reaching across to the burner. The area around the pilot should be inspected for cleanliness. Lint or foreign material must be removed with a brush or vacuum. Figure 106 Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com... -
Page 48: Thermocouple
MAINTENANCE THERMOCOUPLE MAINTENANCE The Element4 fireplaces have two thermocouples; one next to the pilot and one opposite the pilot side of the burner. The completeness and operation of both must be checked. A qualified installer must confirm that both thermocouples are in place and not damaged. -
Page 49: Warranty
Installer: Please complete this form. Customer: Please retain this information. Model Modore 75H (check one) Purchased From Date of Purchase Installed By Date of Installation Fireplace Serial Number Fuel Type Total Venting Horizontal Total Venting Vertical Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com... -
Page 50: Massachusetts Certification
Gas Fitters has issued approval number G1-0515-495 for this appliance. The following must be observed when installing the Element4 fireplaces within the Commonwealth of Massachusetts: (a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole... -
Page 51: Troubleshooting Flowchart
Motor not operating Replace gas valve. properly. Micro switch not Replace gas valve. operating properly. 2nd thermocouple Confirm integrity of 2nd thermocouple and not connected connection. (continued) Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com I:\DEPARTMENTS\Technical Support\Troubleshooting\Guides\20181205_Troubleshooting Flow Chart_E4_8btn Edition.indd... - Page 52 Short between interrupter block and TC- Check connection to interrupter block. cable. Sparking stops after pilot is lit. Electronic measuring amplifier defective. Replace the receiver. (continued) Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
- Page 53 Turn the control knob to “ON” position, a Manual knob is in the “MAN” position. positive latch is required. Main burner is lit. Confirm correct gas pressure. Increase pilot Pilot flame is too low. flame if necessary. (continued) Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
- Page 54 Test the batteries, replace if necessary. Receiver batteries low. Quality 1.5V AA alkaline recommended. Magnet unit drops Ensure magnet unit is operating while motor turns. Test the receiver output to the magnet unit. normally. Receiver makes 3 beeps. Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com (continued)
- Page 55 Check venting for complete integrity. Reduce the primary air opening until flames have blue Too much primary air. base and yellow upper two-thirds. Flames are stable but too small and blue. NORMAL OPERATION Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
- Page 56 APPENDIX TWO Remote/Reciever Combonations Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
-
Page 57: Installing The Optional Wall Switch
Increase the flame height: Press and hold the UP button. • Decrease the flame height: Press and hold the DOWN button. • For fine adjustment tap the UP or DOWN button as necessary. • Turn fireplace OFF: Press the ON/OFF button. Figure 109 Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com... -
Page 58: Connecting To A Smart Home System
Frequent ON and OFF cycles will limit life expectancy of the valve and will increase battery consumption. The fireplace should be powered by the AC adapter for improved reliability and customer satisfaction. Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com... - Page 59 No communication between receiver and Wi-Fi Contact service No control possible by the electronics module Contact service No temperature display in the App • No hand transmitter connected “N.a. ” in the App • Batteries hand transmitter empty Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
- Page 60 2x 1.5 V AAA 4 sec. No reaction from the fireplace No or bad connection between the receiver and Interrupted responses hand transmitter No electronic control No voltage on the receiver Low communication range, AC adapter Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
- Page 61 Try to keep jammers as far away as possible devices can not connect via the 5GHz band, the ProControl from the router. Neighboring wireless networks also play a module is not suitable for 5GHz band. role in the Wi-Fi area. Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
- Page 62 Learances ressures WALL ACCESS dOOR 30 KEY INSTALLATION pOINTS 6 WALL SWITCh Appendix 3 WARRANTY 49 LISTING LAbEL 8 Lp (p ROpANE ONvERSION MAINTENANCE urner Lass iLot herMocoupLes MANTELS 14 Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
- Page 63 NOTES Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
- Page 64 Imported and distributed in North America by: EUROPEAN HOME a division of Europa Ja, Inc. 30 Log Bridge Road Building 300 - Suite 303 Middleton, MA 01949 www.europeanhome.com IGE419-10411 Element4 Gas Fireplaces Rev# 08222019 EuropeanHome.com...
Need help?
Do you have a question about the Modore 75H and is the answer not in the manual?
Questions and answers