Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for H-KING Cessna Skyline
Summary of Contents for H-KING Cessna Skyline
- Page 1 H-King R/C scale model series instruction manual...
-
Page 2: Safety Instructions
SAFETY INSTRUCTIONS 1. Please read this manual carefully and follow the instructions of the manual before you use this products. 2. Our airplane is not a toy, which is only suitable for experienced pilot. Or if you are a novice pilot, please operate under the guidance of an experienced pilot. -
Page 3: Specifications
CONTENTS : 1. Fuselage 7. Spinner 2. Main wing 8. Wing Structs 3. Horizontal tail 9. Philip Screw Driver 4. Rudder 10. Plastic Moulded Antenna 5. Main undercarriage with plastic fairings 11. Accessory pack 6. 3 blade propeller with prop adapter SPECIFICATIONS : - Wing Span : 965mm/37.99in - ESC : 20A Brushless ESC... - Page 4 ASSEMBLY INSTRUCTIONS 1.Install the main undercarriage by slightly holding either side of the landing gear together and then push it into the slot on the fuselage. You will hear a click when it is fully inserted into the slot. 2. Apply foam glue to the horizontal tail as shown. Just apply good enough of glue to the area and don’t apply beyond the width of the tail.
- Page 5 3. Connect the plastic clevis to the control horn. Ensure the servo horn is in 90 degree angle to the pushrod and elevator is in level position. Adjust the plastic clevis by turning clockwise and anti clockwise on the metal push rod to achieve the correct length. 4.
- Page 6 6. Apply glue to rudder fin and install it onto the fuselage as shown. 7. Ensure the rudder fin is squared and perfectly perpendicular to the horizontal tail. 8. Connect the plastic clevises to the rudder control horn. (Ensure the servo horn is in 90 degree angle and rudder is in level position.) Roll the silicon tube onto the plastic clevis to secure the push rod connection.
- Page 7 9. To install the receiver, the cockpit floor has to be removed from the fuselage. The cockpit floor design is precise and tight fitted. So please remove it carefully to avoid making dents on the foam. All the servos wires are well labelled. Please connect the servo leads correspond to the channels on your receiver.
- Page 8 11. You may install the wing onto the fuselage now. Align the plastic dowel on the wing leading edge to the wing saddle bulkhead. Install the nylon wing bolts on the wing as shown. Screw the nylon bolts until the wing is fully seated on the wing saddle. The aileron servos and navigational lights are all hooked up at the same time.
- Page 9 13. Wing structs setup as shown. 14. Apply glue to both of the plastic antennas and stick it on top of the wing.
- Page 10 15. First install the propeller adapter onto the motor shaft then install the big washer as shown 16. Install the 3 blade propeller, add a small washer and tighten it with a lock nut supplied in the kit. Note: Use loctite on all screws and mounting bolts to prevent from loosening during flights.
- Page 11 17. Done! Check the center of gravity and make sure that the CG of the plane should be within the range as indicated. 45-48mm Aileron 12-15mm 12-15mm 12-15mm 12-15mm 12-15mm 12-15mm...
-
Page 12: Esc Manual
ESC Manual This ESC is a beginning level product line designed for fixed wing. It features super smooth start up and throttle linearity, multiple protection, low cost and best performance at this level of product. This is not a toy, only for adult. Age under 14 should be supervised with adult. Please read this manual carefully before using this product for the sake of safety. - Page 13 Input Voltage Programmable 20A ESC lost...
- Page 17 9. Low Voltage Cutoff Type...
Need help?
Do you have a question about the Cessna Skyline and is the answer not in the manual?
Questions and answers