Related Manuals for Assa Abloy Yale Real Living Assure Lock YRC216
Summary of Contents for Assa Abloy Yale Real Living Assure Lock YRC216
- Page 1 Yale Locks YRC216 Z-Wave Plus System Integrators Guide Yale Assure Deadbolt Lock Document Revision: 1 January 2, 2019...
-
Page 2: Table Of Contents
Contents Yale Z-Wave Plus Product Info ........................3 Supported Command Classes ........................3 Association Table ............................ 3 Notifications Table ..........................4 Configurable Parameters ......................... 6... -
Page 3: Yale Z-Wave Plus Product Info
Yale Z-Wave Plus Product Info Manufacturer ID: Assa Abloy (0x0129) Z-Wave Device Type: Door Lock Keypad Z-Wave Role Type: Listening Sleeping Slave (LSS) Product ID: 0x0600 Product Type ID: 0x8004 – YRC216-ZW2 (Push Button Deadbolt) Supported Command Classes Command Class Z-Wave Plus Info... -
Page 4: Notifications Table
Notifications Table Alarm Alarm Reports Alarm Level Description type 0x00 Master code was changed at keypad Master Code changed. 0xFB Master code was changed over RF 0x70 0x(01-max User added User added. Alarm level = user slot number users) 0x(01-max User deleted 0x21 User was deleted. - Page 5 and plays the “Denied”. Trying to duplicate the master code will result in a 0x71 0x00 alarm report. Power to RFM was restored, sent by RF module. The RF Module Power 0x82 0x00 lock doesn’t send any alarm to the RF module when Cycled power is cycled.
-
Page 6: Configurable Parameters
Configurable Parameters Configuration Parameter Size Description Parameters Number Level control, 1 = High Volume, 3 = Silent. Default is 1 Silent mode on/off 1 1 byte or High Volume Auto Relock on/off 2 1 byte 0x00 = OFF, 0xFF = ON default is 0x00 or OFF Auto Relock time 3 1 byte 10 to 180 seconds default is 30 seconds... - Page 7 Yale Assure Lock ® ® Electronic Interconnected Push Button ® Installation and Programming Instructions (YRC216) Inside Outside of Door of Door 4" Touchscreen Shown - 5.5" Available Before you begin Network Module (Optional) DOWNLOAD THE BILT APP for step-by-step installation instructions &...
- Page 8 Before You Begin Template Network Module (Optional) 1/8" 3/32" 1/8" 1" 2-1/8" 4-1/2" (114) 1-3/8" (35mm) Min to 1-3/4" (44.5mm) Max YRL EMICL PBINSTL FUL Rev B...
- Page 9 Mark Door Reference Lines EXISTING 2-3/8" or 2-3/4" Backset Template YRL EMICL PBINSTL FUL Rev B...
- Page 10 Preparing Door (if necessary) Template 4" 5.5" 2-3/8" Ø2-1/8" Ø1" 2-3/4" Drill holes 1/2 way thru door then complete from other side to prevent splitting. YRL EMICL PBINSTL FUL Rev B...
- Page 11 Installing Strike Plates 7-16 / 8-32 x 1" UNCWS Frame 1" Dia. x 1"Deep Frame Inside of Door 1" Dia. x 1/2"Deep Door Frame YRL EMICL PBINSTL FUL Rev B...
- Page 12 Determining Handing The hand of a door is determined from the secure side of the door. The term "secure" means the side from which you initially unlock and enter. Left Hand “ ”, Hinges Left. Left Hand Reverse " ", Hinges Left. Open Inward.
- Page 13 Changing Handing (if necessary) 4" Left Hand to 4" Right Hand Shown 4-24 x 1/4" PPHMS DO NOT TAMPER WITH OR LOOSEN E-CLIP AND ITS ASSEMBLY DO NOT LOOSEN THESE 6 SCREWS OR REMOVE COVER YRL EMICL PBINSTL FUL Rev B...
- Page 14 Changing Handing (if necessary) continued YRL EMICL PBINSTL FUL Rev B...
- Page 15 Lockset Handing Configurations For 5.5" For 5.5" For 4" 4" Right Hand For 4" 4" Left Hand Test Lever and Thumbturn After handing is changed, check that lever and thumbturn rotate freely. YRL EMICL PBINSTL FUL Rev B...
- Page 16 Installing Fire Cups Inside of Door Both Fire Cups and a marked Latchbolt must be used to qualify for listing. YRL EMICL PBINSTL FUL Rev B...
- Page 17 Adjusting Deadbolt Latch (If adjustable deadbolt latch provided) default 2-3/8" position optional 2-3/4" position Pull Press YRL EMICL PBINSTL FUL Rev B...
- Page 18 Installing Deadbolt Latch & Latchbolt 7-16 / 8-32 x 1" UNCWS Inside of Door Bolt must be in retracted (unlocked) position before installing. Ensure arrow stamped on deadbolt Choose latchbolt based on backset. (2-3/8" or 2-3/4") Curved edge of latchbolt faces direction door closes.
- Page 19 Installing Exterior Deadbolt M6x55 PPHMS Inside of Door YRL EMICL PBINSTL FUL Rev B...
- Page 20 Installing Lock Chassis 10-32 x 1-1/2" PPHMS Inside of Door YRL EMICL PBINSTL FUL Rev B...
- Page 21 Securing Back Plate to Door #6-32 x 1/2" POHMS Inside of Door Drill two pilot holes Ø1/8" x 1/2" deep Two #6-32 x 1/2" POHMS screws must be used to qualify for listing. YRL EMICL PBINSTL FUL Rev B...
- Page 22 Testing Deadbolt & Latchbolt Operation Outside of Door YRL EMICL PBINSTL FUL Rev B...
- Page 23 Attaching the Cable Assembly Test that cables are securely connected. Inside of Door Cable must be routed as shown to avoid interference with movement of lock. YRL EMICL PBINSTL FUL Rev B...
- Page 24 Installing Interior Lock Orientation must match. Do not fasten lock to back plate until properly fitted. Inside of Door Turn thumbturn to adjust slot orientation. YRL EMICL PBINSTL FUL Rev B...
- Page 25 Installing Interior Lock continued 10-32 x 5/8" POHMS 6-32 x 1" PPHMS Inside of Door DO NOT LOOSEN THIS SCREW YRL EMICL PBINSTL FUL Rev B...
- Page 26 Installing Interior Lever Inside of Door " SNAP " Inside of Door Pull lever to ensure it is secure. YRL EMICL PBINSTL FUL Rev B...
- Page 27 Testing Final Latchbolt Operation Inside of Door Outside of Door YRL EMICL PBINSTL FUL Rev B...
- Page 28 Testing Final Deadbolt Operation YRL EMICL PBINSTL FUL Rev B...
- Page 29 Testing Final Deadbolt Operation If testing fails, go back to beginning of Step 11 and check installation. YRL EMICL PBINSTL FUL Rev B...
- Page 30 Installing Optional Network Module DO NOT install network module with batteries in unit. Damage may occur. Installing Batteries & Cover Tighten screw to replace cover. Bolt must be in retracted (unlocked) position before installing batteries. YRL EMICL PBINSTL FUL Rev B...
- Page 31 Handing the Lock AFTER installing batteries and cover AFTER a factory reset, create Master code. See 1 of Programming Instructions. After entering the Master code: Press Advanced Lock Settings Press to Select Press Handing the Lock Press to Select Press to complete Lock will cycle motor to complete handing.
- Page 32 Hardware Troubleshooting Cycle lock in both the locked and unlocked positions. If problems are found: Bolt will not extend and motor is grinding a. Enter your Master code. b. With the bolt retracted, press menu Option 3 for Advanced Lock Settings. c.
- Page 33 Changing Lock: Replacing Cylinder 1. To remove cylinder: A. Remove keypad from door. B. Remove rubber gasket. C. Remove two screws holding plastic guide in place. D. Remove plastic guide. E. Remove screw with washer holding cylinder in place (visible after removing plastic guide).
- Page 34 Programming Instructions Low Battery Warning- Flashes RED Lock-out Mode- Keypad Flashes Interior Lock Privacy Mode Button Keypad Master Code must be created before any further programming. Max User Codes = 250 with Z-Wave Plus or ZigBee network module Max User Codes = 25 without network module or with iM1 network module Max User Codes - 12 with Bluetooth YRL EMICL PBINSTL FUL Rev B...
- Page 35 Creating Master Code Creating a Master Code must be performed upon installation or after resetting the lock to factory default. Programming and use of lock is not possible until this step has been successfully completed. Press Press Press Enter 4-8 digit Master Code.
- Page 36 Creating User Codes Master code must be created first. *Max user codes = 250 with Z-Wave Plus or ZigBee network module Max user codes = 25 without network module or with iM1 network module Max user codes - 12 with Bluetooth Enter Master code Press...
- Page 37 Unlocking Door with Code Enter PIN Press "Unlock" Code Chart Duplicate if necessary PIN Code Management (With Network Module - Up to 250 Users) User Type User Name PIN Code Master User User User User User User User User User User User User...
- Page 38 Resetting Lock to Factory Default Interior Lock When resetting the lock, all user codes, including the Master code*, are deleted. All (4" Shown) programming features are reset to original default settings (see below). 1. Remove the battery cover and batteries. 2.
- Page 39 Definitions All Code Lockout Mode: This feature is enabled by the Master code. When enabled, it restricts all user (except Master) code access. When attempting to enter a code while the unit is in Lockout, the keypad flashes 8 times and the lock beeps 3 times as well.
- Page 40 Feature Programming Through Menu Mode Using Master code* 1. Enter 4-8 digit master code* followed by key. 2. Enter digit corresponding to the function to be performed followed by the key. *The Master code must be registered prior to any other programming of the lock. Note: After Master code is entered, lock will automatically hand itself.
- Page 41 Programming Troubleshooting Symptom Suggested Action • Press each keypad button for response when pressed. • Check batteries are installed and oriented correctly (polarity) Lock does not respond – in the battery case. door is open and • Check batteries are in good condition; replace batteries* accessible.
- Page 42 Product Support Tel 1-855-213-5841 • www.yalehome.com Yale® ,Yale Real Living® and Assure Lock® are registered trademarks of Assa Abloy Residential Group. Other products' brand names may be trademarks or registered trademarks of their respective owners and are mentioned for reference purposes only. © Copyright 2018. All rights reserved. Reproduction in whole or in part without the express written permission of Assa Abloy Residential Group is prohibited.
- Page 43 ® ® Yale Real Living Z -Wave Plus Module ® Installation and Programming Instructions ® Installing the Z -Wave Plus Module IMPORTANT: the batteries must be removed prior to removing and/or inserting the network module: • Remove battery cover and batteries. •...
- Page 44 Product Support Tel 800.810.WIRE (9473) • www.yalelocks.com Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company. Copyright © 2016, Yale Security Inc., an ASSA ABLOY Group company.