Subscribe to Our Youtube Channel
Related Manuals for AMS AS5x61 Series
Summary of Contents for AMS AS5x61 Series
- Page 1 User Manual – AS5x61 / AS5x62 Programming AS5x61 /AS5x62 Programming Example www.ams.com Revision 1.0 / 2012/10/31...
-
Page 2: Table Of Contents
User Manual – AS5x61/AS5x62 Programming Table of Contents General Description ....................... 2 Requirements – Applies to all output types ................3 AS5x62 Programming ......................3 AS5x61 Programming ......................8 Copyright ............................. 13 Disclaimer ........................... 13 www.ams.com Revision 1.0 / 10/31/12 page 1/14... -
Page 3: General Description
The ASx61 / AS5x62 operates at a supply voltage of 5V and the supply and output pins are protected against overvoltage up to +20V. In addition the supply pins are prote cted against reverse polarity up to –20V. The Demo software for programminf is available on the Webpage. www.ams.com www.ams.com Revision 1.0 / 10/31/12... -
Page 4: Requirements - Applies To All Output Types
3. AS5x62 Programming 1) Connect AS5x61/AS5x62 to UART Interface board or to communication equipment. Use VCC, GND and OUT for the communication. If the ams UART Interface board is used, please connect an external 5V Powersupply to the board. 2) Start AS5x61/AS5x62 Evaluation Software www.ams.com... - Page 5 This is V at the final magnet position. 10) Enter Clamping Level Low is the voltage at the lower guard band. 11) Enter Clamping Level High is the voltage at the upper guard band. www.ams.com Revision 1.0 / 10/31/12 page 4/14...
- Page 6 Direction: Set the right direction for the Application, CCW or CW. This will calculate the real values (scale factor, Breakpoint…). All this 15) Click information, in addition to voltages and angles, is needed to program the AS5x62. Example:1 Quadrant www.ams.com Revision 1.0 / 10/31/12 page 5/14...
- Page 7 31) Reset the device. You have to push the reset button on the UART Interface board by hand. This will reset the programming configuration. 32) Go to Step 4 to repeat procedure to change unacceptable parameters. www.ams.com Revision 1.0 / 10/31/12 page 6/14...
- Page 8 44) Click yes to accept. CAUTION: Once this is done, the AS5x62 will permanently be programmed. 45) Once the message disappears, the part is programmed. 46) Confirm proper operation by applying a scope or multimeter to VOUT. www.ams.com Revision 1.0 / 10/31/12 page 7/14...
-
Page 9: As5X61 Programming
4. AS5x61 Programming 1) Connect AS5x61/AS5x62 to UART Interface board or to communication equipment. Use VCC, GND and OUT for the communication. If the ams UART Interface board is used, please connect an external 5V Powersupply to the board. 2) Start AS5x61/AS5x62 Evaluation Software... - Page 10 BP_T2: BP setting related to T2 position. Set value into BPWT2D field HystLevel: Only used with 1Q 0 – 360° to move the BP. 14) Additional Settings: Direction: Set the right direction for the Application, CCW or CW. www.ams.com Revision 1.0 / 10/31/12 page 9/14...
- Page 11 21) To program an AS5261(DualDie) Device, redo step 18 to step 20 for the Top Device. 22) Two actions can happen at this point. a. You can confirm that the entered data operates as expected. Go to Step 23. www.ams.com Revision 1.0 / 10/31/12 page 10/14...
- Page 12 35) For programming the A5261(DualDie), redo point 34 and 35 at 36) Click 37) Click This will cause the AS5x61 to permanently enter into Output Mode when power is applied to it. 38) Click 39) Click www.ams.com Revision 1.0 / 10/31/12 page 11/14...
- Page 13 43) Click yes to accept. CAUTION: Once this is done, the AS5x61 will permanently be programmed. 44) Once the message disappears, the part is programmed. 45) Confirm proper operation by applying a scope to VOUT. www.ams.com Revision 1.0 / 10/31/12 page 12/14...
-
Page 14: Copyright
No obligation or liability to recipient or any third party shall arise or flow out of ams AG rendering of technical or other services.
Need help?
Do you have a question about the AS5x61 Series and is the answer not in the manual?
Questions and answers