Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
M-10 Series Copyboard
Assembly and Setup Manual
This is the installation and assembly manual for the M-10S/M-10W Copyboard.
To the Customer
Specialized techniques are required in the wall mounting of the Copyboard. Please do not
attempt any installation work unless you have the techniques.
To the Dealer or Installation Tradesman
In the interest of the safety of the customer, please perform installation work paying due
attention to the strength of the installation location to ensure that it can bear the load of
the Copyboard, printer, and installation parts.
1. Please Read in the Interest of Safety ........................................................ 2
2. Packaging List ............................................................................................. 2
3. Copyboard Installation Procedure ............................................................ 3
4. Assembly of the stand ................................................................................ 3
5. Wall Mounting .............................................................................................. 6
6. Assembly of the Printer Tray ...................................................................... 9
7. Printer Installation .................................................................................... 10
8. Test Print .................................................................................................... 12
9. Fluorescent Lamp Replacement .............................................................. 13
10. Changing the Height of the Unit ............................................... Rear cover
TABLE OF CONTENTS
Advertisement
Table of Contents
Related Manuals for Plus M-10 Series
Summary of Contents for Plus M-10 Series
-
Page 1: Table Of Contents
M-10 Series Copyboard Assembly and Setup Manual This is the installation and assembly manual for the M-10S/M-10W Copyboard. To the Customer Specialized techniques are required in the wall mounting of the Copyboard. Please do not attempt any installation work unless you have the techniques. -
Page 2: Please Read In The Interest Of Safety
PLEASE READ IN THE INTEREST OF SAFETY Warning • Please be sure to perform the installation and assembly based on this manual. Incorrect installation or assem- bly will be the cause of injury. • Please have 2 or more persons lift the Copyboard when installing or removing it. •... -
Page 3: Copyboard Installation Procedure
3. COPYBOARD INSTALLATION PROCEDURE The installation method will change depending on the type of installation. Please perform installation and assem- bly according to the following procedures. ● When using the stand Assembly of the stand See Page 3 * The stand may be an option. Assembly of the printer tray See Page 9 * The printer may be an option. - Page 4 (3) Attach the two horizontal bars to the T-shape legs. T-shaped leg Use hexagonal socket screws and flat washers to attach. Partially fasten using the supplied hexagonal wrench, then tighten securely after the upper and lower hori- zontal bars have been attached. Horizontal bar Hexagonal socket screw Flat washer...
- Page 5 (6) Insert the stay between the printer tray and stand. Tilt the bottom of the main unit slightly forwards and insert the stay between the printer tray and pipe. Pushing the main unit back towards the stand, insert the groove in the stay into the printer tray. Note Check again that the grooves in the stand’s hooks are securely inserted in the mounting holes in the support fittings.
-
Page 6: Wall Mounting
5. WALL MOUNTING (1) Determining the installation location 1200mm The diagram indicates the dimensions of the installa- tion positions. The installation position is the same for both the standard type and the wide type. The installation of the Copyboard to the wall is per- formed after the printer tray is assembled and attached to the Copyboard. - Page 7 (2) Stick the cushions on the printer tray, then mount the printer tray on the main unit. Peel off the protective sheets from the cushions’ adhesive surfaces. Stick the cushions (2) on the back of the bracket. Protective sheet on adhesive surface Cushion Cushions...
- Page 8 (4) Attaching and anchoring the Copyboard to a wall or wall support fitting. (The anchoring method will differ depending on the wall mounting method.) Installing on a Concrete Wall Anchor nut, etc. M6 screw Mounting to a Post M6 wood screw...
-
Page 9: Assembly Of The Printer Tray
6. ASSEMBLY OF THE PRINTER TRAY (1) Temporarily fasten the right and left brackets to the Copyboard using four M4 screws in the order of Steps M4 screws Front screw hole M4 screws Right bracket Left bracket Front screw hole When mounting the printer tray after installing the Screws hole main unit on a wall... -
Page 10: Printer Installation
7. PRINTER INSTALLATION The installation method for the printer will differ depending on your printer*. Please see your printer manual. An example of a printer installation is described below. (1) The USB cable (supplied with the Copyboard) is used to connect the printer connector of the Copyboard with the USB connector of the printer. - Page 11 (3) Fasten the power cable and the USB cable with the supplied cable clips. .Raise the band of the clip, dis- .After finishing the cable .Remove the backing paper from engage it from the hook, and pull wiring, pass the band end the rear surface of the clip and it out.
-
Page 12: Test Print
8. TEST PRINT The first time the printer is used, preparations must be performed such as installing the printer cartridge and removing the protective transportation sheet. Please see your printer manual for details. (1) Switch on the printer power. (2) Open the top cover and open the paper tray. (3) Install the print cartridge in the printer. -
Page 13: Fluorescent Lamp Replacement
When a black band appears at the top and bottom portions of the print or memory storage image, it is time to replace the fluorescent lamp. Please inquire with your dealer or PLUS Vision sales office concerning the replacement of the fluorescent lamp. When replacing the fluorescent lamp, be certain to disconnect the power cable before- hand. -
Page 14: Changing The Height Of The Unit
10. CHANGING THE HEIGHT OF THE UNIT This is the height adjustment to the stand* at the time of setup. The height can be changed among 3 levels in 100 mm units (1770, 1870, and 1970 mm (the maximum height)). Please lock the casters by pressing the lower portion of the lock buttons of them. - Page 15 2003 14-2097-03B...