Kenwood NX-800 Service Manual page 65

Panel Tuning Mode
■ Preparations for tuning the transceiver
Before attempting to tune the transceiver, connect the
unit to a suitable power supply.
Whenever the transmitter is turned, the unit must be
connected to a suitable dummy load (i.e. power meter).
The speaker output connector must be terminated with
a 4Ω dummy load and connected to an AC voltmeter and an
audio distortion meter or a SINAD measurement meter at all
times during tuning.
■ Transceiver tuning (To enter tuning mode)
To enter tuning mode, press the [ ] key while the trans-
ceiver is in test mode. Use the [ ] key to write tuning data
through tuning modes, and the [ ]/[ ] key to adjust tuning
requirements (1 to 4096 appears on the LCD).
Use the [ ] key to select the adjustment item through
tuning modes. Use the [ ] key to adjust 5 reference level
adjustments, and use the [ ] key to switch between Wide/
Narrow/Very narrow.
• LCD display in panel tuning mode
CV voltage, AD value, etc
Sub LCD display 2 . 6
A n
Main LCD display
An: Analog narrow mode
Aw: Analog wide mode
Nn: NXDN narrow mode
Nv: NXDN very narrow mode
Adjustment point
L,L',C,H',H
■ Key operation
Key
Push
[ ] / [ ] Adjustment value up/down Continuation up/down
[ ] / [ ] Volume up/down
[ ] Auto adjustment start
[ ] Wide/Narrow/Very narrow
[ ] Shift to panel test mode
To enter 5 reference level
[ ]
adjustments L/L'/C/H'/H
Writes the adjustment
[ ]
value
[ ] Go to next adjustment item Back to last adjustment item
Microphone key
[PTT] Transmit
[0] to [9]
and [A]
-
to [D],
[#], [ ]
ADJUSTMENT /
C NT R 2 5 6
Adjustment value
(1~4096)
Proper value guide
(When the frequency
adjustment is necessary,
▼ or ▲ is displayed.)
Adjustment item
Function
Hold (1 second)
Continuation up/down
-
-
-
-
-
-
-
调整
面板调谐模式
■ 调谐车载对讲机的准备
在尝试调谐车载对讲机前，请将车载对讲机连接到合适的
电源上。
发射打开时， 车载对讲机必须连接到合适的等效负载上 ( 如
功率表 )。
扬声器输出连接器必须端接 4Ω 的等效负载，调谐期间，
必须始终连接到交流电压表和音频失真仪或 S I N A D 测量仪表
上。
■ 车载对讲机调谐 ( 进入调谐模式 )
要进入调谐模式，请在车载对讲机处于测试模式时按 [ ]
键。用 [ ] 键写入调谐模式的调谐数据，用 [
调整调谐要求 (LCD 上出现 1 到 4096)。
用 [ ] 键选择调谐模式的调整项目。用 [
点基准电平调整，然后用 [ ] 键切换宽 / 窄 / 超窄。
• 面板调谐模式时的 LCD 显示
CV电压、AD值等
副LCD显示
2 . 6
A n C
主LCD显示
An: 模拟窄模式
Aw: 模拟宽模式
Nn: NXDN窄模式
Nv: NXDN超窄模式
调整点
L, L', C, H', H
调整项目
■ 键操作
键
按下
[ ]/[ ] 调整值递增 / 递减
[ ]/[ ] 音量升高 / 降低
[ ] 自动调整开始
[ ] 宽 / 窄 / 超窄
[ ] 换到面板测试模式
进入 5 点基准电平调整
[ ]
调整点 L/L'/C/H'/H
[ ] 写入调整值
[ ] 转到下一调整项目
麦克风键
[PTT] 发射
[0] 至 [9]
和
-
[A] 至 [D],
[#],[ ]
NX-800
] / [ ] 键
] 键调整 5
NT R 2 5 6
调整值(1〜4096)
特征值指引
（需进行频率调整时，
显示▼或▲。 ）
功 能
按住 (1 秒钟 )
连续增加 / 减小
连续升高 / 降低
-
-
-
-
-
返回到最后调整的项目
-
-
65