Kenwood NX-800 Service Manual page 63

"FNC" not appears on the sub LCD display
Key
Function
Microphone key
[PTT] Transmit
Use as the DTMF keypad.
[0] to [9]
If a key is pressed during
and [A]
transmission, the DTMF
to [D],
corresponding to the key
[#], [ ]
that was presses is sent.
"FNC" appears on the sub LCD display
Key
Function
[ ] -
[ ] Analog/NXDN
[ ] / [ ] Function off
[ ] -
[ ] LCD all lights
[ ] High power/Low power
[ ] Function off
[ ] Compander on/off
[ ] Beat shift on/off
Microphone key
[PTT] Transmit
[0] to [9]
and [A]
Function off
to [D],
[#], [ ]
• LED indicator
Red LED Lights during transmission.
Green LED Lights when there is carrier.
• Sub LCD indicator
"FNC" Appears at function on.
• LCD display in panel test mode
(Power ON)
Market code
(After 2sec.)
Temperature
+ 2 5
Sub LCD display
A n SQ 5
Main LCD display
An: Analog narrow mode
Aw: Analog wide mode
Nn: NXDN narrow mode
Nv: NXDN very narrow mode
ADJUSTMENT /
Display
-
-
Display
Analog: "A"
NXDN: "N"
-
-
LCD all point appears
Low: icon appears
-
On: icon appears
On: icon appears
-
C UH F F 2
Frequency range
"F2": 400~470MHz
1 - 1
Signaling No.
Channel No.
Squelch level
(Analog mode only)
调整
副 LCD 显示上不出现"FNC"
键
功 能
麦克风键
[PTT] 发射
[0] 至 [9] 用作 DTMF 键盘。如果在
和 发射时按下某个键，则
[A] 至 [D], 发送与按下的键对应的
[#],[ ]
DTMF。
副 LCD 显示上出现"FNC"
键
功 能
[ ] -
[ ] 模拟 /NXDN
[ ]/[ ] 功能关
[
] -
[ ] LCD 全亮
[ ] 高功率 / 低功率
[ ] 功能关
[ ] 压扩器打开 / 关闭
[ ] 拍频偏移打开 / 关闭
麦克风键
[PTT] 发射
[0] 至 [9]
和
功能关
[A] 至 [D],
[#],[ ]
• LED 指示灯
红色 LED 发射时点亮。
绿色 LED 有载波时点亮。
• 副 LCD 指示
"FNC" 功能开启时出现。
• 面板测试模式时的 LCD 显示
(打开电源）
市场代码
（2秒后）
温度
+ 2 5
副LCD显示
A n SQ 5
主LCD显示
An: 模拟窄模式
Aw: 模拟宽模式
Nn: NXDN窄模式
Nv: NXDN超窄模式
NX-800
显 示
-
-
显 示
模拟 :"A"
NXDN:"N"
-
-
LCD 全点显示
低 : 图标出现
-
开 : 图标出现
开 : 图标出现
-
C UH F F 2
频率范围
"F2" : 400~470MHz
1 - 1
信令号
信道号
静噪电平
（仅模拟模式）
63