Kenwood NX-800 Service Manual page 84

NX-800
Item
Panel tuning mode
3. High 1) Adj item: [HIPWR]
Transmit Adjust: [✳✳✳✳]
Power 2) Adj item:
adjust [L HIPWR]→
[L' HIPWR]→
[C HIPWR]→
[H' HIPWR]→
[H HIPWR]
Adjust: [✳✳✳✳]
PTT: ON
Press [ ] key to store
the adjustment value.
4. Low 1) Adj item: [LOPWR]
Transmit Adjust: [✳✳✳✳]
Power 2) Adj item:
adjust [L LOPWR]→
[L' LOPWR]→
[C LOPWR]→
[H' LOPWR]→
[H LOPWR]
Adjust: [✳✳✳✳]
PTT: ON
Press [ ] key to store
the adjustment value.
5. Balance 1) Adj item: [BAL]
adjust *2 Adjust: [✳✳✳]
Deviation meter
LPF: 3kHz
HPF: OFF
2) Adj item: [L BAL]→
[L' BAL]→[C BAL]→
[H' BAL]→[H BAL]
Adjust: [✳✳✳]
PTT: ON
Press [ ] key to store
the adjustment value.
Sub LCD:
Tone frequency
[ ] key: Press while
transmitting to change
20Hz and 2kHz.
*2: Refer to the "Necessary Deviation adjustment item for each signaling and mode" table on page 92.
Balance adjustment is common with the adjustment of all signaling deviation.
6. Maximum 1) Adj item: [Nn NDEV]
Deviation Adjust: [✳✳✳✳]
(NXDN) Deviation meter
adjust *3 LPF: 3kHz
HPF: OFF
[Narrow] 2) Adj item:
[NnL NDEV]→
[NnL' NDEV]→
[NnC NDEV]→
[NnH' NDEV]→
[NnH NDEV]
Adjust: [✳✳✳✳]
PTT: ON
Press [ ] key to store
the adjustment value.
84
ADJUSTMENT
Condition
PC test mode
equipment
1) Adj item: [High Power
Transmit Power] meter
2) Adj item: [Low], Ammeter
[Low'], [Center],
[High'], [High]
PTT: Press
[Transmit] button.
Press [Apply All]
button to store the
adjustment value.
1) Adj item: [Low
Transmit Power]
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
PTT: Press
[Transmit] button.
Press [Apply All]
button to store the
adjustment value.
1) Adj item: [Balance] Deviation
Deviation meter meter
LPF : 3kHz Oscilloscope
HPF : OFF
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
PTT: Press
[Transmit] button.
Press [Apply All]
button to store the
adjustment value.
[2kHz Sine Wave
Check box]: Check
while transmitting
change to 2kHz.
1) Adj item: [Maximum Deviation
Deviation (NXDN meter
Narrow)] Oscilloscope
Deviation meter
LPF: 3kHz
HPF: OFF
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
PTT: Press
[Transmit] button.
Press [Apply All]
button to store the
adjustment value.
Measurement
Test-
Unit Terminal Unit
ANT
ANT
Adjustment
Specifi cations /
Parts Method
[Panel 25.0W ±1.0W
tuning 9.0A or less
mode]
[ ],[ ] [PC test mode]
Press [Apply All]
[PC test button to store the
mode] adjustment value
[ ],[ ] after all adjustment
point was adjusted.
5.0W ±0.5W
5.0A or less
[PC test mode]
Press [Apply All]
button to store the
adjustment value
after all adjustment
point was adjusted.
The Deviation of 2kHz Tone deviation
20Hz frequency is is within ±1.0% of
fi xed. Change the 20Hz tone devia-
2kHz adjustment tion.
value to become
the same deviation [PC test mode]
of 20Hz within the Press [Apply All]
specifi ed range. button to store the
adjustment value
after all adjustment
point was adjusted.
[Panel 3056Hz ±50Hz
tuning
mode] [PC test mode]
[ ],[ ] Press [Apply All]
button to store the
[PC test adjustment value
mode] after all adjustment
[ ],[ ] point was adjusted.
Remarks