Comeup H-2500 Instruction Manual

Comeup H-2500 Instruction Manual

Cable puller

Advertisement

PN:487265 220V/50Hz、486122 230V/50Hz、489635 110V/50Hz
483636 240V/50Hz、483958 240V/50Hz、482316 220V/60Hz
486280 230V/50Hz、487655 110V/50Hz、487705 110V/60Hz、487281 110V/50Hz

Introduction

 Feature
Drum type
Pulling capacity kg
50 Hz
Rope speed m / min
60 Hz
Gear train
Gear ratio
Motor rating IP44 , kw x p
width
Drum dimension mm
drum dia.
flange dia.
Percentage Duty Cycle
 Unpacking
.Rope arm
.Base plate,except for PN:489635
.Wire rope 8 mm x 50 m, except for PN:489635 483958
.Detachable rope storage roller
2
.Foot control kit with 2.0 mm
x 3C x 2 m lead
.Power lead 1.5 mm
2
x 3C x 3 m and plug
.Power lead 2.0 mm
2
x 3C x 3 m and plug for PN:487705
 Read this manual carefully
You should carefully read and understand this manual before operating it.
Careless winch operation may result in personal injury hazards or property
damage.
 Information requesting or parts ordering
Please specify the followings information:
.Winch PN
.Part description
.Quantity for each part
CABLE PULLER
H-2500
Model:
Large Drum
Small Drum
1,500
2,500
4.0
2.5
5.0
3.0
hypoid gear plus spur gears
154:1
0.6 x 4
124
104
130
74
166
94
25% ED
1pc
1pc
1pc
1pc
1pc
1pc
1pc
.Serial number
.Replacement part number

Installation

1. Install this machine on the ground horizontally.
2. Confirm that the machine voltage complies with the power source.
3. Connect the power cord with the power source, set the over – load
protection switch in to the "RESET" position.
4. Press the "Foot Control" down, the drum rotates in a clockwise direction and
make sure there is no noisy sound level or malfunction.
5. Release the "Foot Control" to have an emergency stop. The brake performs
inter – locked and motor has instantly hold the load while power failure.
 Wiring Diagram

Warning

.The cable puller is not intended to be used in any manner for the movement or
lifting of personnel
.The rated capacity shown is based on the first layer of rope on the drum
. The rope winding on the drum shall remain 5 wraps from the drum

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the H-2500 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Comeup H-2500

  • Page 1 Installation CABLE PULLER 1. Install this machine on the ground horizontally. H-2500 Model: 2. Confirm that the machine voltage complies with the power source. 3. Connect the power cord with the power source, set the over – load PN:487265 220V/50Hz、486122 230V/50Hz、489635 110V/50Hz protection switch in to the “RESET”...
  • Page 2 Winch Assembly Parts List Ref No. Description Part Number Drum A kit 880873 Motor kit, 110V/220V, 60Hz 880896 Motor kit, 110V/220V/230V, 50Hz 880897 Motor kit, 120V/240V, 50Hz 880898 Motor kit, 110V/220V, 60Hz 883099 shaft 880874 gear 880875 shaft 880876 gear 880877 gear 880878...

Table of Contents