Subscribe to Our Youtube Channel
Related Manuals for Allied Telesis AT-TQ1402 Series
Summary of Contents for Allied Telesis AT-TQ1402 Series
-
Page 1: Installation Guide
AT-TQ1402 Series Wireless Access Point AT-TQ1402 AT-TQm1402 4680 Installation Guide 613-002709 Rev. B... - Page 2 Allied Telesis, Inc. has been advised of, known, or should have known, the...
-
Page 3: Declaration Of Conformity
AT-TQ1402 Series Wireless Access Point Installation Guide Electrical Safety and Emissions Standards This product meets the following standards: “Federal Communications Commission Interference Statement” “European Union Restriction of the Use of Certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment” on page 4 “Safety and Electromagnetic Emissions”... - Page 4 European Union Restriction of the Use of Certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment This Allied Telesis RoHS-compliant product conforms to the European Union Restriction of the Use of Certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment. Allied Telesis ensures RoHS conformance by requiring supplier Declarations of Conformity, monitoring incoming materials, and maintaining manufacturing process controls.
- Page 5 AT-TQ1402 Series Wireless Access Point Installation Guide Wire Communication • IEEE 802.1 • IEEE 802.3 • IEEE 802.3u • IEEE 802.3x • IEEE 802.3af Wireless Communication • IEEE 802.11 DSSS • IEEE 802.11a OFDM • IEEE 802.11b DSSS/FHSS • IEEE 802.11g OFDM •...
- Page 6 Electro Magnetic Interference (EMI) • FCC part15 Subpart B/ Class B • EN55032 Class B • CISPR 32 • VCCI Class B • VCCI-CISPR 32:2016 • AS/NZS CISPR 32 Electro Magnetic Susceptibility (EMS) - EN55024 and EN55035 • IEC 61000-4-2:2008 •...
-
Page 7: Translated Safety Statements
• AS/NZS CISPR 32: 2015 • AS/NZS 4268: 2017 Translated Safety Statements Important: The indicates that a translation of the safety statement is available in a PDF document titled Translated Safety Statements on the Allied Telesis website at www.alliedtelesis.com/ support. -
Page 9: Table Of Contents
LAN Port .............................. 23 Redundant Power Supply .......................... 25 LEDs ................................26 Cable Specifications........................... 27 AT-TQ1402 Series Wireless Access Point Installation ................29 Review Safety Precautions ........................30 Unpack Shipping Box Contents ......................... 32 Installation Guidelines ..........................33 Install Access Point ............................ 34 General Installation Guidelines...................... - Page 10 Contents...
-
Page 11: List Of Figures
List of Figures Figure 1: Top View ............................20 Figure 2: Front Edge View ..........................21 Figure 3: Back Edge View ..........................21 Figure 4: Acceptable Orientations on a Tabletop, Wall and Ceiling Installation ..........33 Figure 5: Attach Screws to Access Point Chassis ................... 36 Figure 6: Adjust Screws on Access Point...................... - Page 12 List of Figures...
- Page 13 List of Tables Table 1. Primary Port for Power Source ......................25 Table 2. LED Status Information ........................26 Table 3. Shipping Box Components ....................... 32 Table 4. Physical Specifications ........................45 Table 5. Environmental Specifications ......................45 Table 6. Input Power Specifications ....................... 46 Table 7.
- Page 14 List of Tables...
-
Page 15: Preface
Preface This guide contains the hardware installation instructions for the AT-TQ1402 Series Wireless Access Point. This preface contains the following sections: “Safety Symbols Used in this Document” on page 16 “Contacting Allied Telesis” on page 17 ... -
Page 16: Safety Symbols Used In This Document
Preface Safety Symbols Used in this Document This document uses the following conventions. Note Notes provide additional information. Caution Cautions inform you that performing or omitting a specific action may result in equipment damage or loss of data. Warning Warnings inform you that performing or omitting a specific action may result in bodily injury. -
Page 17: Contacting Allied Telesis
AT-TQ1402 Series Wireless Access Point Installation Guide Contacting Allied Telesis If you need assistance with this product, you may contact Allied Telesis technical support by going to the Support & Services section of the Allied Telesis web site at www.alliedtelesis.com/support. You can find links for the following services on this page: 24/7 Online Support —... - Page 18 Preface...
-
Page 19: Product Description
Chapter 1 Product Description This chapter describes the hardware components of the AT-TQ1402 Series Wireless Access Point. This chapter contains the following sections: “Overview” on page 20 “Features” on page 22 “LAN Port” on page 23 “Redundant Power Supply” on page 25 ... -
Page 20: Overview
Power On/Off button Reset button Kensington lock port for physical security in your installation environment. The top view of the AT-TQ1402 Series is illustrated in Figure 1. Back Edge AT-TQ1402 5GHz 4681 Front Edge Figure 1. Top View... -
Page 21: Figure 2: Front Edge View
AT-TQ1402 Series Wireless Access Point Installation Guide The front edge view of the AT-TQ1402 Series is illustrated in Figure 2. 4683 Mounting Bracket Thumb Screw Hole Figure 2. Front Edge View The back edge view of the AT-TQ1402 Series is illustrated in Figure 3. -
Page 22: Features
Chapter 1: Product Description Features This section lists the main features of the AT-TQ1402 Series Wireless Access Point. Hardware The hardware features are as follows: Features One fixed 10/100/1000 BASE-T port (RJ-45) in dual function mode to support IEEE standard 802.3af compliance powered device (PD) mode of PoE. -
Page 23: Management Access
LAN Port The AT-TQ1402 Series Access Point is equipped with one Ethernet port - LAN. The LAN port is capable of receiving PoE power (powered device port) as the primary power or standing by as the backup power source for an external power supply unit. - Page 24 Chapter 1: Product Description Speed The LAN port can operate at 10/100 Mbps or 1000 Mbps. The speed is set automatically with Auto-Negotiation. You cannot disable Auto-Negotiation on the port. Note The LAN port should be connected to a network device that also adjusts its speed with Auto-Negotiation.
-
Page 25: Redundant Power Supply
AT-TQ1402 Series Wireless Access Point Installation Guide Redundant Power Supply The AT-TQ1402 Series Access Point offers a redundant power supply system. In addition to the power supply through the DC-IN jack, the access point has one PoE-capable LAN port (LAN). The external power supply connected to the DC-IN jack is the primary power source for the unit. -
Page 26: Leds
Chapter 1: Product Description LEDs The LEDs on the AT-TQ1402 Series Access Point top panel display the status information. This LED display status information is given in Table 2. Table 2. LED Status Information State Description GREEN AT-TQ1402 Series is powered ON and operating normally. -
Page 27: Cable Specifications
AT-TQ1402 Series Wireless Access Point Installation Guide Cable Specifications The AT-TQ1402 Series Access Point is connected to your local area network with Ethernet cables from Ethernet ports LAN. Refer to “Cable Specifications” on page 48 for the specifications of these cables. - Page 28 Chapter 1: Product Description...
-
Page 29: At-Tq1402 Series Wireless Access Point Installation
Chapter 2 AT-TQ1402 Series Wireless Access Point Installation This chapter describes how to install the AT-TQ1402 Series Access Point. It contains the following sections: “Review Safety Precautions” on page 30 “Unpack Shipping Box Contents” on page 32 “Installation Guidelines” on page 33 ... -
Page 30: Review Safety Precautions
Chapter 2: AT-TQ1402 Series Wireless Access Point Installation Review Safety Precautions Please review the following safety precautions before you begin to install the access point. Important: Safety statements that have the symbol are translated into multiple languages in the Translated Safety Statements document, which is available at www.alliedtelesis.com/library. - Page 31 AT-TQ1402 Series Wireless Access Point Installation Guide Warning This equipment shall be installed in a Restricted Access location. Warning FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
-
Page 32: Unpack Shipping Box Contents
Chapter 2: AT-TQ1402 Series Wireless Access Point Installation Unpack Shipping Box Contents To unpack the AT-TQ1402 Series Access Point from the shipping box, perform the following procedure: 1. Remove all components from the shipping box. Note Store the packaging material in a safe location so that if you need to return the unit to Allied Telesis, you will have the original shipping material available. -
Page 33: Installation Guidelines
If the primary power for the access point is to be the external power supply (not provided with the AT-TQ1402 Series Access Point), ensure that an AC power outlet is within six feet of the planned installation site. (Refer to Table 6 on page 46 for the power supply AC power specifications.) -
Page 34: Install Access Point
“Ceiling or Wall - Attach Chassis to Mounting Bracket” on page 42 General The AT-TQ1402 Series Access Point can be mounted on a table, wall, or hard-surface celling. The general installation guidelines are as follows: Installation Guidelines Read “Review Safety Precautions” on page 30. -
Page 35: Ceiling Or Wall - Mounting Bracket Installation
AT-TQ1402 Series Wireless Access Point Installation Guide 3. The installation of your AT-TQ1402 Series Access Point on the table top surface is now complete. Ceiling or Wall - This section explains how to install the access point on a ceiling or wall that consists of a hard surface. -
Page 36: Figure 5: Attach Screws To Access Point Chassis
Chapter 2: AT-TQ1402 Series Wireless Access Point Installation Pre-Fit Mounting Bracket on AT-TQ1402 Series Access Point To pre-fit the access point on the mounting bracket, perform the following procedure: 1. Install the two screws (provided) in the bottom side of the access point chassis. -
Page 37: Figure 7: Remove Mounting Bracket From Access Point
AT-TQ1402 Series Wireless Access Point Installation Guide 3. Tighten the screws so that they touch the mounting bracket plate and then loosen them by approximately 1/4 turn. Note Adjust the access point chassis screws so they are loose enough to... -
Page 38: Figure 8: Mark And Pre-Drill Holes For Key-Hole Slots
Chapter 2: AT-TQ1402 Series Wireless Access Point Installation 2. Using the mounting bracket as a template, mark the two key-hole slots with a pencil in the location and orientation where you want to install the access point. Refer to the arrows in Figure 8. -
Page 39: Figure 10: Pre-Drill Holes For Mounting Bracket
AT-TQ1402 Series Wireless Access Point Installation Guide 5. Secure the physical position of the mounting bracket by pre-drilling holes through the two existing open bracket mounting holes in the opposite corners from the key-hole slots. Refer to the arrows in Figure 10. -
Page 40: Install Ethernet Cable And External Dc Power Supply
PoE power. For the PoE input power specifications, refer to “PoE Power Requirements” on page 47. 3. Depending on the primary power source for the AT-TQ1402 Series Access Point, perform one of the following steps: a. -
Page 41: Install Anti-Theft Device
Figure 13. Connect External AC/DC Power Adapter Cable 3. Connect the external power supply AC plug to an appropriate AC power source. 4. On the AT-TQ1402 Series chassis, push the DC Power Button to the “IN” position to turn ON the power supply at the chassis. Note The DC Power Button controls power to the DC-IN jack only. -
Page 42: Ceiling Or Wall - Attach Chassis To Mounting Bracket
Chapter 2: AT-TQ1402 Series Wireless Access Point Installation 2. If you are installing your AT-TQ1402 Series on a table top surface, your unit is now ready for use. 3. If you are installing your AT-TQ1402 Series on the ceiling or wall installation, go to “Ceiling or Wall - Attach Chassis to Mounting... -
Page 43: Figure 16: Seat Access Point Onto Mounting Bracket
AT-TQ1402 Series Wireless Access Point Installation Guide 4690 Figure 16. Seat Access Point onto Mounting Bracket 3. Tighten the bracket thumbscrew into the front of the chassis until it is securely fastened. Refer to Figure 17. 4691 Figure 17. Securely Fasten Chassis to Mounting Bracket with Thumbscrew 4. -
Page 44: Start Initial Management Session
Chapter 2: AT-TQ1402 Series Wireless Access Point Installation Start Initial Management Session This section contains an abbreviated version of the procedure to start the initial management session. For complete instructions, refer to the AT-TQ1402 Series Wireless Access Point Series User’s Guide. -
Page 45: Technical Specifications
Parameter Specification Dimensions (W x D x H) 163 mm x 165 mm x 40.5 mm (6.42 in. x 6.50 in. x 1.59 in.) Weight (AT-TQ1402 Series with 567 g (1.25 lb) mounting bracket) Environmental Specifications Table 5. Environmental Specifications... -
Page 46: Power Specifications
Appendix A: Technical Specifications Power Specifications Input Power The power specifications for the AT-TQ1402 Series Access Point are given in Table 6. Specifications Table 6. Input Power Specifications Parameter Specification Rated Input Voltage 12 VDC Maximum Input Current 0.7 A Average Input Current 0.52 A... -
Page 47: Poe Power Requirements
The AT-MWS0091 (WA-24Q12R) external power supply is not supplied or shipped with the AT-TQ1402 Series Access Point product. PoE Power The AT-TQ1402 Series Access Point power requirements for the LAN PoE port are given in Table 8. Requirements Table 8. PoE Power Requirements... -
Page 48: Cable Specifications
Appendix A: Technical Specifications Cable Specifications The AT-TQ1402 Series Access Point Ethernet cable requirements for the LAN ports are listed in Table 9. Table 9. LAN Port Twisted Pair Cable Requirements 10 Mbps 100 Mbps 1000 Mbps Cable Type Standard TIA/EIA 568-A-compliant... -
Page 49: Lan Port Specifications And Pinouts
AT-TQ1402 Series Wireless Access Point Installation Guide LAN Port Specifications and Pinouts Port The AT-TQ1402 Series Access Point port specifications are shown in Table 10. Specifications Table 10. LAN Port Specifications Connector Specification Standards - LAN IEC603-7 (10/100/1000 Base T) PoE standard - LAN IEEE 802.3af (class 3) -
Page 50: Table 12. Mdi-X Pin Signals (10Base-T Or 100Base-Tx)
Appendix A: Technical Specifications Table 12 lists the pin signals for the MDI-X configuration at 10/100 Mbps. Table 12. MDI-X Pin Signals (10Base-T or 100Base-TX) Signal Table 13 lists the pin signals when the LAN port is operating at 1000 Mbps. -
Page 51: Regulatory Statements
Appendix B Regulatory Statements This appendix contains the following regulatory statements: “Federal Communication Commission Interference Statement” on page 52 “Europe - EU Declaration of Conformity” on page 54 ... -
Page 52: Federal Communication Commission Interference Statement
Appendix Appendix B: Regulatory Statements Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. - Page 53 AT-TQ1402 Series Wireless Access Point Installation Guide Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your...
-
Page 54: Europe - Eu Declaration Of Conformity
20 cm between Statement the radiator and your body. Importer Allied Telesis International BV Incheonweg 7, 1437 EK Rozenburg Note Contact Allied Telesis for the EU conformity statement. To contact Allied Telesis, visit our web site at www.alliedtelesis.com/contact.
Need help?
Do you have a question about the AT-TQ1402 Series and is the answer not in the manual?
Questions and answers