Table of Contents
Advertisement
Thank you for trusting Prestige products! If you are a consumer, please note:
Professional installation is strongly recommended.
This manual assumes the installer has adequate knowledge of the following expertise. Therefore, it does not
cover these topics in detail:
•
12-volt electronics
•
Testing and verifying circuits
•
Making safe and lasting wiring connections
•
Factory ignition, power, lighting, data bus and sensing systems
•
Factory systems and components to avoid
•
Safe wire routing, circuit protection and product placement
•
Access to vehicle-specific technical information
In addition, this manual assumes the installer has the proper tools, skill and facilities to perform a professional installation.
Performing an improper installation could result in damage to the vehicle or its components, improper system function,
unsafe vehicle operation or physical injury. Such instances would not be covered by the vehicle manufacturer's warranty,
nor by Voxx Electronics, Inc.
Detailed Descriptions
2
2
3
4
External Components
4
5
LED / Valet Programming Button
4
System Operation
4
4
Alarm Override Procedures
5
5
6
2018 Voxx Electronics Corporation. All rights reserved.
APS25Z
Vehicle Security / Keyless Entry System
Installation and Reference Guide
8
System Programming
8
Programming Mode Entry / Exit
9
9
9
9
9
System Diagnostics
9
9
11
Wiring Diagrams
11
14
Starter Kill Relay
25
Full System Connections
APS25Z_RevA_08/18
Advertisement
Table of Contents
Related Manuals for Prestige APS25Z
Summary of Contents for Prestige APS25Z
-
Page 1: Table Of Contents
Vehicle Security / Keyless Entry System Installation and Reference Guide Thank you for trusting Prestige products! If you are a consumer, please note: Professional installation is strongly recommended. This manual assumes the installer has adequate knowledge of the following expertise. Therefore, it does not cover these topics in detail: •... -
Page 2: Wire Harness Colors And Functions
Detailed Descriptions: Wire Harness Colors and Functions Main Input / Output Connector (11-pin connector) See page 15 for the full system diagram. These wires are listed in order of their placement in the harness connector. 10 11 1. WHITE – Parking Light Relay Output (Internal Relay Pin 30) At its default setting, the WHITE wire supplies 12-Volt (+) or Ground (-) to the vehicle's park light wire based on the connection of the relay input (WHITE/RED wire). -
Page 3: Door Lock Connector
Detailed Descriptions: Wire Harness Colors and Functions Main Input / Output Connector (11-pin connector) See page 15 for the full system diagram. These wires are listed in order of their placement in the harness connector. 7. YELLOW – Ignition Input (+) The YELLOW wire connects to the vehicle's primary ignition wire. -
Page 4: Shock Sensor
Shock Sensor The shock sensor plugs into a 4-pin connector on the Prestige module. It should be securely attached to a vehicle surface or sturdy wire harness. Testing takes place after all connections are made and the system is powered up. -
Page 5: Setup Options
Detailed Descriptions: Setup Options Bank 1: Add / Remove Remote Controls Remote programming is located in Feature Bank 1. This system will Auto Program basic functions of the remote with one (1) button press. Basic functions are channels 1-3, Lock, Unlock, and Trunk / Start. Feature Bank 1 Description 1 Auto Program/Lock... -
Page 6: Security Control
Detailed Descriptions: Setup Options Security Control (Bank 2) See page 8 for Programming Instruction. Options Feature Bank 2 1 Chirp 2 Chirp 3 Chirp 4 chirp 5 Chirp 6 Chirp 1 Lock / Unlock Function 500ms 3.5sec 500ms L, Dbl UL DBL L, 500ms UL DBL L, DBL UL 500ms L, 350ms UL... - Page 7 Detailed Descriptions: Setup Options Security Control (Bank 2) (cont.) See page 8 for Programming Instruction. Feature 5: Automatic Arming Function: Set the system to arm automatically after exiting the vehicle. Setting Choices: • Option 1 - System will arm and doors will lock only when the alarm is armed from the remote control. •...
-
Page 8: Quick Reference
Quick Reference: System Programming Programming Mode Entry and Exit Procedure Once the system is installed and powered up, you will use the vehicle ignition, override button and a programmed remote control to set all system options. Feature options are divided into categories, or Banks, as described throughout this section. -
Page 9: Feature Bank Options
With Arm & Disarm Dome Light Delay To program the Prestige system to wait until the dome light turns off before arming: 1. Close all doors. 2. With the vehicle ignition off, press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK, UNLOCK, LOCK on the remote control. The dash-mounted LED will turn on. -
Page 10: Silent Arm And Disarm
Quick Reference: System Programming & Diagnostics Silent Arm and Disarm Program the Prestige system to arm and disarm without notification beeps. (The siren will sound if the system is triggered while armed.) 1. Turn the ignition ON then OFF. 2. Press and release the valet/programming button three (3) times. The system will respond with one (1) beep for ON or two (2) beeps for OFF. -
Page 11: Door Lock Connections
Quick Reference: Wiring Diagrams Door Lock Connections Negative-Trigger Door Locks Verification: The vehicle wires register Ground when the Lock and Unlock switches are activated. RED ( - ) Lock Output Lock Vehicle Door Lock Control Relays Unlock GREEN ( - ) Unlock Output Positive-Trigger Door Locks Verification: The vehicle wires register 12V+ when the Lock and Unlock switches are activated. - Page 12 Quick Reference: Wiring Diagrams Door Lock Connections Single-Wire Negative Multiplex Door Locks (Relays required) Verification: The vehicle wire registers variable Ground values when the Lock and Unlock switches are activated. Please consult the vehicle-specific wire and location chart for resistor values. Ground Fused +12 Volt RED ( - ) Lock Output...
- Page 13 Quick Reference: Wiring Diagrams Door Lock Connections Reverse-Polarity Door Locks (Relays required) Verification: The vehicle wires rest at Ground and register 12V+ when the Lock and Unlock switches are activated. Fused +12 Volt Battery Souce RED ( - ) Lock Output Lock To Door Lock Motor Unlock...
- Page 14 Quick Reference: Wiring Diagrams Starter Kill / Anti-Grind Relay Connections Included Starter Kill / Anti-Grind Relay To ORANGE - Starter Kill / To Vehicle Ignition Anti-Grind Output (-) From Alarm APS25Z_RevA_08/18...
- Page 15 Quick Reference: Wiring Diagrams APS25Z_RevA_08/18...