Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Advantech PCL-733
Summary of Contents for Advantech PCL-733
- Page 1 PCL-733 32-channel Isolated Digital Input Card...
- Page 2 Co.,Ltd.assumesnoresponsibilityforitsuse,norforanyinfringe- mentsoftherightsofthirdpartieswhichmayresultfromitsuse. Acknowledgments PC-LabCard is a trademark of Advantech Co., Ltd. IBM and PC are trademarks of International Business Machines Corporation. MS- DOS, Microsoft C and Quick BASIC are trademarks of Microsoft Corporation. BASIC is a trademark of Dartmouth College. Intel is a trademark of Intel Corporation.
-
Page 3: Table Of Contents
Contents Chapter 1 General Information ........1 Introduction Introduction Introduction Introduction Introduction ......................................2 2 2 2 2 Features Features Features ..................................2 2 2 2 2 Features Features ......... Applications Applications ................ -
Page 5: Chapter 1 General Information
General Information Chapter 1 General Information 1 1 1 1 1... -
Page 6: Introduction Introduction
ThePCL-733has32isolated,bidirectionaldigitalinputchannels, which provide 2,500 V of protection. The PCL-733 offers two PC interruptswithjumper-selectableIRQ.Eachinputchannelcorre- sponds to a bit in a PC I/O port, making the PCL-733 very easy to program. Features • 3 2 i s o l a t e d ,b i d i r e c t i o n a ld i g i t a li n p u tc h a n n e l s •... - Page 7 Specifications • • • • • Input voltage: Input voltage: Input voltage: Input voltage: Input voltage: 5 to 24 V • • • • • Input resistance: Input resistance: Input resistance: Input resistance: 1.2 KW @ 0.5 W Input resistance: •...
- Page 8 4 4 4 4 4 PCL-733 User's Manual...
-
Page 9: Chapter 2 Installation
Installation Chapter 2 Installation 5 5 5 5 5... -
Page 10: Switch And Jumper Settings Switch And Jumper Settings
Initial Inspection We carefully inspected the PCL-733 both mechanicallyand electrical- lybeforeshipment.Itshouldbefreeofmarksandinperfectorderon r e c e i p t . As you unpack the PCL-733, check it for signs of shipping damage (damagedbox,scratches,dents,etc.).Ifitisdamagedorfailstomeet specifications,notifyourservicedepartmentoryourlocalsales representativeimmediately.Also,callthecarrierimmediatelyand retaintheshippingcartonandpackingmaterialforinspectionbythe carrier.Wewillthenmakearrangementstorepairorreplacetheunit. Dischargeanystaticelectricityonyourbodybeforeyoutouchthe board by touching the back of the system unit (grounded metal). -
Page 11: Locating Switches And Jumpers
PC L- 733 32- channelI sol at ed D i gi t alI nputM... -
Page 12: Base Address Selection (Sw1)
. We set the PCL-733 for a base address of Hex 300 at the factory. If you need to adjust it to some other address range, set switch SW1 as... -
Page 13: Interrupt Level (Jp1)
Interrupt level (JP1) JumperJP1selectstheinterruptlevelsforchannel0andchannel16. 15 12 11 10 7 5 3 2 DI16 To disable one or both of the interrupts, simply remove the jumper clips,whichyoumaystoreinthejumpersotheydon'tgetlost.See below: 15 12 11 10 7 5 3 2 DI16 Interrupt triggering (JP2, JP3) JumpersJP2andJP3selectthetriggeredge(risingorfalling)on whichDI0andDI16,respectively,willtriggeraninterrupt.Default jumpersettingsappearbelow:... -
Page 14: Hardware Installation Hardware Installation
. 5 . Remove the screw that secures the expansion slot cover to the systemunit.Savethescrewtosecuretheinterfacecardretaining b r a c k e t . 6 . Carefully grasp the upper edge of the PCL-733 card. Align the holeintheretainingbracketwiththeholeontopoftheexpansion slotandalignthegoldstripededgeconnectorwiththeexpansion slotsocket.Presstheboardfirmlyintothesocket. -
Page 15: Chapter 3 Signal Connections And Register Format
Signal Connections and Register Format Chapter 3 Signal Connections and Register Format... -
Page 16: Connector Pin Assignments Connector Pin Assignments
IDI3 IDI4 IDI5 IDI6 IDI7 EI.GND1 IDI8 IDI9 IDI10 IDI11 IDI12 IDI13 IDI14 IDI15 EI.GND2 IDI16 IDI17 IDI18 IDI19 IDI20 IDI21 IDI22 IDI23 EI.GND3 IDI24 IDI25 IDI26 IDI27 IDI28 IDI29 IDI30 IDI31 EI.GND4 12 12 12 12 PCL-733 User's Manual... -
Page 17: Isolated Input Isolated Input
Isolated Input The PCL-733 has 32 isolated digital inputs, which accept 5-24 V and havearesistanceof1.2kW. Every8inputsshareoneexternalground (EI.GND). The following figure shows how to connect an external i n p u ts o u r c et ot h ec a r d ' si s o l a t e di n p u t s :... - Page 18 14 14 14 14 PCL-733 User's Manual...
-
Page 19: Pc I/O Port Address Map
PC I/O Port Address Map Appendix A PC I/O Port Address Map... - Page 20 LPT1: (1stprinterport) 380 - 3AF Reserved 3B0 - 3BF Mono Display/Print adapter 3C0 - 3CF Reserved 3D0 - 3DF Color/Graphics 3E0 - 3EF Reserved 3F0 - 3F7 Floppy diskdrive 3F8 - 3FF COM1: 16 16 16 16 PCL-733 User's Manual...
Need help?
Do you have a question about the PCL-733 and is the answer not in the manual?
Questions and answers