1. Manuals
  2. Brands
  3. Woods Manuals
  4. Farm Equipment
  5. 208-2
  6. Operator's manual

Woods 208-2 Operator's Manual

Rotary cutter
Hide thumbs
Table of Contents

Advertisement

Quick Links

ROTARY CUTTER
208-2
M208-2
Serial Number 3000 & Above
Tested. Proven. Unbeatable.

Advertisement

Table of Contents
loading

Related Manuals for Woods 208-2

Summary of Contents for Woods 208-2

  • Page 1 ROTARY CUTTER 208-2 M208-2 Serial Number 3000 & Above Tested. Proven. Unbeatable.
  • Page 2 Dealer Check List items have been completed. The dealer is to return the prepaid postage portion to Woods, give one copy to the customer, and retain one copy. Failure to complete and return this card does not diminish customer’s warranty rights.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS INTRODUCTION ..........ii SPECIFICATIONS .

  • Page 4: Specifications

    80 HP with heat-treated alloy steel gears, heat-treated vertical shafts and lubricated tapered roller bearings (Input Box) 80 HP Function The 208-2 & M208-2 model cutters are designed for mowing large areas of grass, crop residue or brush up to 1-1/2" diameter. GENERAL INFORMATION ARNING The purpose of this manual is to assist you in operating and maintaining your cutter.

  • Page 5: Safety Rules

    SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! PREPARATION Safety is a primary concern in the design and manufacture of our products. Unfortunately, our Check that all hardware is properly installed. efforts to provide safe equipment can be wiped Always tighten to torque chart specifications out by an operator’s single careless act.

  • Page 6: Safety Decals

    SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) edly and cause severe injury or death. Follow Oper- ator's Manual instructions for working underneath Remove accumulated debris from this equip- and blocking requirements or have work done by a ment, power unit, and engine to avoid fire hazard.
  • Page 7 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! sure, set parking brake, stop engine, remove key, On mounted units with optional hydraulic cut- and unfasten seat belt. ting height adjustment, use a double-acting cylin- der with a maximum extended length of 28-1/4" Before performing any service or maintenance, from attaching point center to center.
  • Page 8 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) Frequently check blades. They should be sharp, Leak down or failure of mechanical or hydraulic free of nicks and cracks, and securely fastened. system can cause equipment to drop. Do not handle blades with bare hands.
  • Page 9 SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! Pull-Type Unit Mounted Unit Note: Shield shown must be used for Pull-Type Pull-Type Units with Unit square driveshafts (splined Pull-Type driveshaft) Unit (square driveshaft) 11 - SERIAL NUMBER PLATE 1 - PN 18864 MODEL NO.
  • Page 10 SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 2 - PN 15502 4 - PN 15503 WARNING DANGER ROTATING COMPONENTS Do not operate without cover in place. Look and listen for rotation. Do not open cover until all components have stopped.
  • Page 11 13 - PN 33347 Replacement safety decals can be ordered free DAN ER from your Woods dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.

  • Page 12: Operation

    OPERATION ARNING Safety is a primary concern in the design and manufacture of our products. Unfortunately, our Before performing any service or maintenance, efforts to provide safe equipment can be wiped disconnect driveline from tractor PTO. out by an operator’s single careless act. Before working underneath, disconnect drive- In addition to the design and configuration of line, raise cutter, lock in transport position, and...
  • Page 13 ATTACHING CUTTER TO TRACTOR Place transport bar in stored position before using hydraulic cylinder or ratchet to adjust cutting height. ARNING Mounted Make sure attachment is properly secured, ARNING adjusted, and in good operating condition. Make sure spring-activated locking pin or collar A minimum 20% of tractor and equipment slides freely and is seated firmly in tractor PTO weight must be on the tractor front wheels when...
  • Page 14 DB2171 Approximate Hole in Hole in Cutting Tailwheel Tailwheel Height Brace (12) Tube Asy (11) DB2169 1" 2" 1. Tractor rockshaft arm 3" 2. Connecting link 3. Lower lift arm 4" 4. Tractor top link 5. Cutter mast plate 5" 6.
  • Page 15 ___Check and keep all bystanders away from equip- the cutter. The operator should understand how to, and ment work area. be prepared to, stop tractor and cutter quickly in an emergency. ___Check all lubrication points and grease as instructed in "Service, lubrication information". Take all possible precautions when leaving tractor and cutter unattended: disengage PTO, lower cutter to ___Check to be sure each gearbox is half-full of a high...
  • Page 16 the opposite cutting edge of the blade. All blades, except the reversible blades, are for a specific spindle rotation. Be sure they are installed on the correct spin- RAISED TRANSPORT dle. Refer to the Owner Service section for blade instal- POSITION lation.

  • Page 17: Owner Service

    OWNER SERVICE equipment for eyes, hair, hands, hearing, and head; Safety is a primary concern in the design and and respirator or filter mask where appropriate. manufacture of our products. Unfortunately, our Stop power unit and equipment immediately efforts to provide safe equipment can be wiped upon striking an obstruction.
  • Page 18 side to side and front to rear movement. The pull-type Use a lithium base grease with a No. 2 NGLI consis- unit will be anchored front to rear. tency for all locations. Be sure to clean fittings thor- oughly before attaching grease gun. For the mounted unit, tighten tractor lower 3-point arm anti-sway mechanisms to prevent side to side move- One good pump of most guns is sufficient.
  • Page 19 DB1136A DESCRIPTION FREQUENCY Tailwheel hub 10 hrs. Ratchet height adjustment (optional) 100 hrs. Tailwheel pivot and hub (single or dual optional on mounted units) 10 hrs. PTO Shaft, (mounted) lube all four sides of shaft and both U-joints (see * in fig- Daily ure 6) PTO Shaft, (pull-type) access under shield;...
  • Page 20 BLADE SERVICING stump jumpers on the crossbar. When installation is complete, blade should be snug, but still swivel on pin ARNING without excessive force. Retain any spacers not used in shimming blade. Use Before working underneath, disconnect drive- them when installing new blades or when blade wear line, raise cutter, lock in transport position, and occurs.
  • Page 21 A = 1.75” 1--3/4” CD5205 1. Yoke and splined shaft 2. U-Joint repair kit 3. Back-Up plate 4. Friction disc 5. Clutch yoke and plate 6. Clutch hub assembly DB2160 7. Bushing 1. Clutch shaft 9. Compression 8. Compression spring 2.
  • Page 22 To Free a Seized Clutch CHAIN SHIELDING REPAIR A new slip clutch, or one that has been in storage over the winter, may seize. DANGER To free a seized clutch, shut the tractor off and remove driveline. Completely loosen the six bolts to remove all Full chain shielding, designed to reduce the tension from springs.

  • Page 23: Dealer Service

    DEALER SERVICE The information in this section is written for dealer edly and cause severe injury or death. Follow Oper- service personnel. The repair described here requires ator's Manual instructions for working underneath special skills and tools. If your shop is not properly and blocking requirements or have work done by a equipped or your mechanics are not properly trained in qualified dealer.
  • Page 24 Damage Inspection Leakage at the top cover, horizontal seal or between Do not replace gears unless deep gouges, chips, deep horizontal housing and gearbox housing can be pitting or deep wear grooves are present. corrected without removing gearbox from cutter. Inspect gear shafts and sleeves.
  • Page 25 Place seal squarely on housing (spring-loaded lip Turn gear shafts to ensure they turn freely and seals toward gearbox). Select a seal driver, a piece of pipe or are not dragging. tubing with an OD that will set on outside edge of seal cage but will clear housing.
  • Page 26 CROSSBAR INSTALLATION CD4002 1. 1-5/8 x 2-5/16” x 7 CD3739 GA Washer 2. Anti-wrap washer 3. Crossbar 1. Using emery cloth (220 or finer), remove surface Figure 12. Anti-Wrap Washer Installation rust, and foreign material from gearbox, vertical The anti-wrap washer (2) was added as an inline shaft, and crossbar.
  • Page 27 NOTE: Omit step 2 when installing a clamp-type 4. When are certain you have correctly crossbar. determined the proper shim pack, remove crossbar and apply blue Loctite® retaining compound to vertical shaft. When fit between shaft and crossbar is tight, use Loctite® sparingly. When fit is loose, “A”...
  • Page 28 1. Yoke 2. Cup and bearings 3. Snap ring 4. Journal cross Figure 13. U-Joint Exploded View U-Joint Disassembly 1. Remove external snap rings from yokes in four locations as shown in Figure 14. CD1330 6. When installing a clamp-type crossbar, install clamp bolts and torque to 85 lbs.-ft.
  • Page 29 3. Clamp cup in vise as shown in Figure 16 and tap U-Joint Assembly on yoke to completely remove cup from yoke. 1. Place seals securely on bearing cups. Insert cup Repeat Step 2 & Step 3 for opposite cup. into yoke from outside and press in with hand pressure as far as possible.

  • Page 30: Assembly Instructions

    DEALER SET-UP INSTRUCTIONS CAUTION Assembly of this cutter is the responsibility of the WOODS dealer. It should be delivered to the owner Always wear relatively tight and belted clothing completely assembled, lubricated and adjusted for to avoid getting caught in moving parts. Wear normal conditions.
  • Page 31 REAR DRIVE & SLIP CLUTCH INSTALLATION 1. Bolt 2. Lock clip 3. Keyhole plate 4. Spacer 5. Spacer 6. Spacer 7. Crossbar 8. Blade 9. Pin DB1954 DB2195A Figure 19. Blade Assembly 7. 5/8 NC x 3-1/2 Hex 1. Slip clutch head cap screw 2.
  • Page 32 208-2 PULL-TYPE ASSEMBLY locknut (8). Repeat for opposite side of tongue. Tighten hardware. Tailwheel Yoke & Tailwheel Installation Install parking jack (1) and secure to tongue. Attach wheel yoke tube (6) to rear of cutter by aligning it with the three attachment points. Slide clevis brackets of tube over the attachment points and attach with clevis pin (10).
  • Page 33 Optional Hydraulic Cylinder or Ratchet Ratchet adjustment link (10) may be installed in place of hydraulic cylinder. Use same attaching hardware. Adjustment Installation (Figure 23) H-Frame Installation (Figure 25) Attach H-frame (1) to cutter tongue. Place cup washer (21) on bolt (19), then insert spacer (20) into H-frame and install bolt through spacer.
  • Page 34 1. H-Frame 2. Hydraulic hose holder 3. Front 2/3 of 3-joint drive 4. Upper drive shield CD5207 5. Rear 1/3 of 3-joint 10. 3/16 x 1” Cotter pin 11. 3/8 x 1” Bolt 12. 3/8” Lockwasher 13. 1/2 x 5-1/2” Bolt 14.
  • Page 35 DC2162A 1. H-Frame 2. Hydraulic hose holder 3. Front 2/3 3-joint drive 4. Drive shaft shield 5. Shield support 6. Shield strap 10. 3/16 x 1” Cotter pin 11. 1/4 x 1/2” Stove bolts 12. 1/4” Hex locknut 13. 3/8 x 1” Bolt 14.
  • Page 36 Category 1 Assembly (MTD) (Figure 26) Attach right A-frame half (1) and left A-frame half (2) to The mounted 208-2 is available for Category 1 and top hole of cutter mast by placing washer (13) and Category 2, 3-point hitch tractors. It is also available sleeve (12) on bolt (14).
  • Page 37 Attach right A-frame half (1) and left A-frame half (2) to (14) through next hole in pivot arm (4) and through top hole of cutter mast by inserting hitch pin (14) sleeve (5) in rear slot of top link weldment (6). Secure through top hole of cutter mast and placing sleeve (15), both bolts with lockwasher (12) and nut (13).
  • Page 38 Single or Dual Tailwheel Installation (MTD) Single Tailwheel Installation (MTD) (Figure Attach adjustment braces (2) to lower holes of center brackets at rear of cutter with bolt (4) and nut (5) as shown. Attach tailwheel arm assembly (1) to lugs at rear center of cutter frame with clevis pin (3) and cotter pins (8) as shown.
  • Page 39 Chain Shielding Installation (Figure 32) age property. If this machine is not equipped with full chain shielding, operation must be stopped when anyone comes within several hundred feet. WARNING Install chain shielding as shown, inserting bolts from inside out. Be sure to use flange locknuts (7) on front Full chain shielding, designed to reduce the shields, and locknuts (6) on rear chain shielding.
  • Page 40 Adjustable Side Skid Installation Quick Coupler Bushing Kit Installation (Optional) (Optional) Attach side skid (2) to frame (1) as shown, inserting Place sleeve (2) over category 2 pin and secure with carriage bolts from inside frame. spiral pin (3). When you have determined the desired cutting height, adjust your side skids.

  • Page 41: Trouble-Shooting

    TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Does not cut Dull blades Sharpen blades. Worn or broken blades Replace blades. (Replace in pairs only.) Ground speed too fast Reduce ground speed. Drive not functioning (blades do Check drive shaft connection. not turn when PTO is running) Check gearbox.
  • Page 42 DEALER CHECK LISTS PRE-DELIVERY CHECK LIST ___ Point out the safety decals. Explain their mean- ing and the need to keep them in place and in (DEALER’S RESPONSIBILITY) good condition. Emphasize the increased (Dealer's Responsibility) safety hazards when instructions are not fol- lowed.
  • Page 43 PARTS INDEX Rotary Cutters 208-2 & M208-2 COMMON PARTS MAIN FRAME ASSEMBLY ..........42 INPUT GEARBOX 1:1.35 .
  • Page 44 208-2 & M208-2 MAIN FRAME ASSEMBLY (PULL-TYPE & MOUNTED) DB2153 18 -- Complete English Decal Set 19 -- English Safety Decal Set 20 -- French Safety Decal Set 42 Parts 32394 (Rev. 9/3/2004)
  • Page 45 REF PART DESCRIPTION REF PART DESCRIPTION HARDWARE 32399 Gearbox 1:1.35 11204 13/16 x .010 Shim washer 15194 1-1/4 SQ ID x 2-3/8 Washer 11036 3/4 x 1-1/2 x 18 GA Shim washer 32363 Input gearbox 1:1.35 11041 * 3/8 x 3/8 x 2-7/8 Key 28273 Torsion bar 1287 *...
  • Page 46 208-2 & M208-2 INPUT GEARBOX 1:1.35 (PULL-TYPE & MOUNTED) REF PART DESCRIPTION REF PART DESCRIPTION 32363 Input gearbox 1:1.35 complete 32364 Gear and shaft assembly 7269 3/8 NC x 3/8 Flat point socket set 11209 .010 Gearbox gasket screw 23675 1”...
  • Page 47 208-2 & M208-2 SPINDLE GEARBOX 1:1.35 (PULL-TYPES & MOUNTED) DC2168B REF PART DESCRIPTION REF PART DESCRIPTION 11442 .062 x 4-1/2 ID x 5 Gasket 32399 1:1.35 Repair gearbox 11158 Vertical gear and shaft assembly, HT 7832 * 5/8 NC x 1-1/2 HHCS HT 11114 Bearing cone, 2.891 OD...
  • Page 48 208-2 DRIVE SHAFT & SHIELD ASSEMBLY (PULL-TYPE UNITS ONLY) DC2162A REF PART DESCRIPTION REF PART DESCRIPTION HARDWARE 11940 H-Frame assembly with hardware 1256 * 3/16 x 1 Cotter pin 3443 Hydraulic hose holder 1282 * 1/4 NC x 1/2 Round head screw...
  • Page 49 208-2 REAR DRIVE ASSEMBLY WITH SPLINED TELESCOPIC SHAFT (PULL-TYPE UNITS) NOTE: Four Styles of driveshafts have been used on the 208 series cutters. Check your driveshaft for square, splined, tri-lobe, or two-lobe shape and order repair parts from the correct parts list.
  • Page 50 M208-2 REAR DRIVE ASSEMBLY WITH TRI-LOBE TELESCOPIC SHAFT (MOUNTED UNITS) NOTE: Four Styles of driveshafts have been used on the 208 series cutters. Check your driveshaft for square, splined, tri-lobe, or two- - lobe shape and order repair parts from the correct parts list. M5201 REF PART DESCRIPTION...
  • Page 51 208-2 & M208-2 SLIP CLUTCH ASSEMBLY WITH 1-1/2” SQUARE SLIP SLEEVE SHAFT (PULL-TYPE & MOUNTED) NOTE: Four Styles of driveshafts have been used on A = 1.75” the 208 series cutters. Check your driveshaft for square, splined, tri-lobe, or two- - lobe shape and order repair parts from the correct parts list.
  • Page 52 208-2 FRONT 2/3 DRIVE LINE WITH 1-1/2” SQUARE TELESCOPIC SHAFT NOTE: Four Styles of driveshafts have been used on the 208 series cutters. Check your driveshaft for square, splined, tri-lobe, or two- - lobe shape and order repair parts from the correct parts list.
  • Page 53 208-2 FRONT 2/3 OF 3-JOINT DRIVE FOR SPLINED TELESCOPIC SHAFT (PULL-TYPE UNITS ONLY) NOTE: Four Styles of driveshafts have been used on the 208 series cutters. Check your driveshaft for square, splined, tri-lobe, or two-lobe shape and order repair parts from the correct parts list.
  • Page 54 FRONT 2/3 3-JOINT DRIVE M5963 REF PART DESCRIPTION REF PART DESCRIPTION 40590 Guard, outer half, also includes items 40599 2-Joint shielded 9, 10 and 11 (cut to length) 40574 Yoke, 1-3/8 - 6SP (complete with lock 40591 Guard, inner half, also includes items collar) 9, 10 and 11 (cut to length) Cross and bearing kit...
  • Page 55 208-2 & M208-2 CHAIN SHIELDING (PULL-TYPE & MOUNTED) Part Used Description 28303 3/8 x 52--3/4 Pin, 42--chain 28290 Rear chain shield bundle complete 28297 Left corner chain plate 28293 Rear chain plate 3773 3/8 x 38--1/2 Pin, 31--chain DB2149 28296...
  • Page 56 M208-2 FRONT HALF OF 2-JOINT DRIVE - 1-1/2” SQUARE SHAFT (MOUNTED UNITS ONLY) NOTE: Four styles of driveshafts have been used on the 208 series cutters. Check your driveshaft for square, splined, tri-lobe, or two- - lobe shape and order repair parts from the correct parts list. OPTIONAL Part Used...
  • Page 57 M208-2 DRIVELINE - TWO LOBE SHAFT NOTE: Four Styles of driveshafts have been used on the 208 series cutters. Check your driveshaft for square, splined, tri-lobe, or two- - lobe shape and order repair parts from the correct parts list. CD5578 Part Part...
  • Page 58 M208-2 SLIP CLUTCH DRIVE - TWO-LOBE SHAFT NOTE: Four Styles of driveshafts have been used on the 208 series cutters. Check your driveshaft for square, splined, tri-lobe, or two- - lobe shape and order repair parts from the correct parts list. REF PART DESCRIPTION 45041...
  • Page 59 208-2 REAR HEIGHT ADJUSTMENT ASSEMBLY (PULL TYPE) Part Used Description ---------- Attitude pivot block 12550 Attitude rod assembly 8669 1/4 NPT x 156” High-pressure hose assembly ---------- Rear deck attachment lug ---------- 3-1/2 x 8 Hydraulic cylinder w/ breather (see pg 46 for breakdown) 20380 Transport bar (incl.#18-20)
  • Page 60 M208-2 TAILWHEEL ASSEMBLY (MOUNTED UNITS ONLY) DB2138 Single Dual Part Part Used Description Used Description 32378 Tailwheel arm asy (includes 32378 Tailwheel arm asy (includes items 2 & 22) items 2 & 22) 11011 1--1/2 x 1--5/8 x 1--1/2 Bronze 11011 1--1/2 x 1--5/8 x 1--1/2 Bronze bushing...
  • Page 61 208-2 & M208-2 WHEEL & TIRE (PULL-TYPE & MOUNTED - EARLY STYLE) DC2895 Part Part Used Description Used Description 4984 Heavy hub with long axle 4679 4.00 x 8 Rim half Heavy wheel hub with cups 4676 4.00 x 8 Rim & laminated tire 4”...
  • Page 62 208-2 TAILWHEEL YOKE ASSEMBLY (PULL-TYPE UNITS ONLY) Part Used Description 17507 Wheel yoke arm asy (pneu- matic) 4984 Heavy hub w/long axle 15” 4--Hole rim 32400 Right wheel yoke assembly (for laminated tire) - - or- - - - or- -...
  • Page 63 25860 5/32 x 1-1/4 Drive pin 25861 Jack crank handle 25862 Thrust bearing * Obtain Locally DB1682 208-2 & M208-2 STUMP JUMPER - OPTIONAL (PULL-TYPE & MOUNTED) ONE USED PER SPINDLE Part Used Description 12785 Stump jumper complete 32641 Stump jumper strap...
  • Page 64 208-2 SPRING ARM ASSEMBLY (OPTIONAL) (PULL-TYPE UNITS ONLY) Part Used Description 12006 5/8 NC Elastic stop nut - - or- - - - or- - 2371 * 3/4 NC Hex locknut 12447 5/8 x 3 x 7 GA Hat washer...
  • Page 65 M208-2 LINK & PIVOT ARM ASSEMBLY (MOUNTED UNITS ONLY) DC2164A REF PART DESCRIPTION REF PART DESCRIPTION 12274 * 5/8 NC x 2-1/4 HHCS HT 8417 Frame shipping unit 3632 * 5/8 Standard SAE flat washer 10521 Check chain kit 6239 * 5/8 NC Hex locknut 7906 Lower check chain bracket 13087...
  • Page 66 REF PART DESCRIPTION REF PART DESCRIPTION HARDWARE 10475 208-2 3-1/2 Bore x 8” stroke single- acting hydraulic cylinder, complete 923 * 1/4 X 1-3/4 Cotter pin (Pull-type only) 6698 * 3/8 NC Hex locknut 23540 Seal repair kit (includes 2A thru 2D) 23550 * 3/8 NC x 1-1/2 Socket head cap ----- †...
  • Page 67 M208-2 CATEGORY 1, 3-POINT HITCH ASSEMBLY (MOUNTED UNITS ONLY) Part Used Description 28268 Right A--frame half 28269 Left A--frame half 28306 1--1/8 x 1--7/16 x 11/16 Sleeve HT 1450 * 3/4 NC Hex nut 2522 * 3/4 Standard lockwasher 28285 Top link weldment 27140 3/4 x 1--1/4 x 3 Sleeve...
  • Page 68 208-2 & M208-2 CROSSBAR PULLER (OPTIONAL) (PULL-TYPE & MOUNTED) CD1249A Part Used Description 8811 Crossbar puller complete 19914 Crossbar puller clevis 3097 5/8 NC x 4-1/2 Hex head cap screw GR5 230 * 5/8 NC Hex nut 24879 Pad assembly...
  • Page 69 M208-2 QUICK COUPLER BUSHING KIT (OPTIONAL) (MOUNTED UNITS ONLY) REF PART DESCRIPTION 24845 Quick coupler bushing kit 24795 1-1/8 x 1-7/16 x 2-3/4 Sleeve 26955 7/16 x 1-1/2 Spiral pin DB2152 Parts 67 32394 (Rev. 9/3/2004)

  • Page 70: Bolt Torque Chart

    BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly.
  • Page 71 BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 Metric Bolt Thread Sizes 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG ............. Agriculture NC ............ National Coarse ATF.......Automatic Transmission Fluid NF ............

  • Page 72: Index

    INDEX ASSEMBLY Product Inside Back Cover Replacement Parts Back Cover Dealer Set-Up Instructions 28 OPERATION CHECK LISTS Attaching Cutter to Tractor 11 Delivery (Dealer’s Responsibility) 40 Blades 13 Pre-Delivery (Dealer’s Responsibility) 40 Cutting Height & Attitude Adjustment 11 Pre-Operation (Owners Responsibility) 12 Mowing Tips 13 Pre-Operation Checklist 12 DEALER SERVICE...
  • Page 73 WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the dealer and distributor from whom the purchase was made, transportation charges prepaid.
  • Page 74 Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been materially modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized service center.

This manual is also suitable for:

M208-2

Table of Contents