Set Serial - Panasonic AK-HRP200G Operating Instructions Manual

Setup.Mode.Operations.
Save.remote.camera.configuration.file.to.memory.card
1..
Press.<SAVE/LOAD>.to.select.[ND].
• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (Load).
ND
M.GAIN
2..
Press.<UP>.or.<DOWN>.to.select.a.file.number.on.the.
memory.card.and.press.<EXECUTE>.to.confirm.the.
selection.
ND
M.GAIN
When saving to file number 2 on the memory card
3..
Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
• Do not remove a memory card that is being accessed.
ND
M.GAIN
• To cancel saving, select [n] and press <EXECUTE>.
• The file is saved to the memory card and [Fin] appears when saving
ends.
• [E02] is displayed if the save operation to the memory card fails.
If this happens, check the memory card and try again or insert
another memory card to perform the operation again.
• [E01] is displayed when a remote camera configuration file with the
same name as the one you are attempting to save already exists on
the memory card. To overwrite the file, press <UP> or <DOWN> to
select [y] and press <EXECUTE>.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
Load.remote.camera.configuration.file.from.memory.
card
Remote camera configuration file data loaded from the memory card is
returned to the operating status.
1..
Press.<SAVE/LOAD>.to.select.[CC].
Each press of <SAVE/LOAD> toggles between [ND] (Save) and [CC]
(Load).
ND
M.GAIN
2..
Press.<UP>.or.<DOWN>.to.select.a.file.number.on.the.
memory.card.and.press.<EXECUTE>.to.confirm.the.
selection.
ND
M.GAIN
When loading file number 2 on the memory card
(continued)
CC SHT SYNC
M.PED
IRIS
CC SHT SYNC
M.PED
IRIS
CC SHT SYNC
M.PED
IRIS
CC SHT SYNC
M.PED
IRIS
CC SHT SYNC
M.PED
IRIS
3..
Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
• Do not remove a memory card that is being accessed.
ND
M.GAIN
• To cancel loading, select [n] and press <EXECUTE>.
• The file is loaded from the memory card and [Fin] appears when
loading ends.
• [E02] is displayed if the load operation from the memory card fails.
If this happens, check the memory card and see whether the file
exists on the memory card. If it does, start over from step 1.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
15.Set.serial
Press <SELECT> to select menu number [15].
1 (Select CCU serial)/
2 (Select remote camera serial)
UP
ND
M.GAIN
DATA
SET
DOWN
DISPLAY SELECT
SET UP ND/CC M.GAIN/M.PED SHUTTER
SHIFT
+
SAVE/LOAD
UP+DOWN
Press to exit setup mode (hold down)
Setting.CCU.serial
Press <UP> or <DOWN> to select [1] and press <EXECUTE> to confirm
the selection.
ND
M.GAIN
• After the selection is confirmed, the unit restarts automatically.
Setting.remote.camera.serial
Press <UP> or <DOWN> to select [2] and press <EXECUTE> to confirm
the selection.
ND
M.GAIN
• After the selection is confirmed, the unit restarts automatically.
Setting.for.camera.recorder.serial
Press <UP> or <DOWN> to select [3] and press <EXECUTE> to confirm
the selection.
ND
M.GAIN
• After the selection is confirmed, the unit restarts automatically.
CC SHT SYNC
M.PED
IRIS
CAMERA
CC SHT SYNC
M.PED 10-19
No.
IRIS
SELECT
EXIT EXECUTE
Press to confirm
Press to select the
menu number
CC SHT SYNC
M.PED
IRIS
CC SHT SYNC
M.PED
IRIS
CC SHT SYNC
M.PED
IRIS
17