Set Ip Address; Set Subnet Mask - Panasonic AK-HRP200G Operating Instructions Manual

Setup.Mode.Operations.
2..
Press.<UP>.or.<DOWN>.to.select.7-segment.display.
brightness.and.press.<EXECUTE>.to.confirm.the.
selection.
ND
M.GAIN
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
10.Set.IP.address
1.. Press.<SELECT>.to.select.menu.number.[10].
• Block 1 of the IP address appears.
Press to select
the IP address
UP
ND CC
M.GAIN
DATA
SET
DOWN DISPLAY SELECT
SET UP ND/CC M.GAIN/M.PED SHUTTER
SHIFT
+
SAVE/LOAD
UP+DOWN
Press to switch the block
Press to exit setup mode (hold down)
2..
Press.<SAVE/LOAD>.to.select.[CC],.[SHT],.and.[SYNC].
• The display changes in the order of block 1, block 2, block 3, and
block 4.
• When changing the IP address, press <UP> or <DOWN> to change
the setting for each block.
ND
M.GAIN
3..
Press.<SHUTTER>.to.confirm.the.IP.address.setting.
• Pressing <SHUTTER> while block 4 is displayed confirms the
setting.
ND
M.GAIN
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• If the IP address setting value has been changed, the unit will
restart automatically when you exit setup mode. If the setting value
has not been changed, the unit will not restart.
• To make other settings, press <SELECT> to select a menu number.
(continued)
CC SHT SYNC
M.PED
IRIS
Display/set block 1
Display/set block 2
Display/set block 3
Display/set block 4
CAMERA
SHT SYNC
M.PED 10-19
No.
IRIS
SELECT
EXIT EXECUTE
Press to confirm
Press to select the
menu number
CC SHT SYNC
M.PED
IRIS
CC SHT SYNC
M.PED
IRIS
11.Set.subnet.mask
1..
Press.<SELECT>.to.select.menu.number.[11].
• Block 1 of the subnet mask appears.
Press to select
the subnet mask
UP
ND CC
M.GAIN
DATA
SET
DOWN DISPLAY SELECT
SET UP ND/CC M.GAIN/M.PED SHUTTER
SHIFT
+
UP+DOWN SAVE/LOAD
Press to switch the block
Press to exit setup mode (hold down)
2..
Press.<SAVE/LOAD>.to.select.[CC],.[SHT],.and.[SYNC].
ND
M.GAIN
• The display changes in the order of block 1, block 2, block 3, and
block 4.
• When changing the subnet mask, press <UP> or <DOWN> to
change the setting for each block.
3..
Press.<SHUTTER>.to.confirm.the.subnet.mask.setting.
ND
M.GAIN
• Pressing <SHUTTER> while block 4 is displayed confirms the
setting.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• If the subnet mask setting value has been changed, the unit will restart
automatically when you exit setup mode. If the setting value has not
been changed, the unit will not restart.
• To make other settings, press <SELECT> to select a menu number.
Display/set block 1
Display/set block 2
Display/set block 3
Display/set block 4
CAMERA
SHT SYNC
M.PED 10-19
No.
IRIS
SELECT
EXIT EXECUTE
Press to confirm
Press to select the
menu number
CC SHT SYNC
M.PED
IRIS
CC SHT SYNC
M.PED
IRIS
15