Setup.mode.operations; Set Camera Number; Save Scene File To/Load Scene File From Memory Card - Panasonic AK-HRP200G Operating Instructions Manual

Setup.Mode.Operations

1.Set.camera.number
1..
Open.setup.mode.and.check.that.menu.number.[1].is.
displayed..If.a.menu.number.other.than.[1].appears,.
press.<SELECT>.to.select.menu.number.[1].
Press to select the camera number
UP
ND CC
M.GAIN
DATA
SET
IRIS
DOWN DISPLAY SELECT
SET UP ND/CC M.GAIN/M.PED SHUTTER
SHIFT
+
UP+DOWN SAVE/LOAD EXIT
Press to exit setup mode
(hold down)
Press to confirm the camera number
2..
Press.<UP>.or.<DOWN>.to.select.a.camera.number.and.
press.<EXECUTE>.to.confirm.the.selection.
ND
M.GAIN
To select camera number 2
• Camera numbers become available after exiting setup mode.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
<Note>
For AK-HC3500A, the camera numbers 1 to 15 are valid. When
connecting to AK-HC3500A, do not set a camera number to 16 or
above.
2.Save.scene.file.to/load.scene.file.from.memory.card
Current operating status data is saved as a scene file to the memory
card.
Press.<SELECT>to.select.menu.number.[2].
Select file number,
Save file indication
Select y (Select)/
Load file indication
n (Cancel)
UP
ND ND
M.GAIN
DATA
SET
DOWN DISPLAY SELECT
SET UP ND/CC M.GAIN/M.PED SHUTTER
SHIFT
+
UP+DOWN SAVE/LOAD
Press to save/load
Press to exit setup mode
(hold down)
10
SHT SYNC CAMERA
M.PED 10-19
No.
SELECT
EXECUTE
Press to select the
menu number
CC SHT SYNC
M.PED
IRIS
CC CC SHT SYNC CAMERA
M.PED 10-19
No.
IRIS
SELECT
EXIT EXECUTE
Press to confirm
Press to select the
menu number
2-1.Save.scene.file.to.memory.card
Before switching to setup mode, open the scene file you wish to save
with the SCENE/USER FILE select buttons. (For details on how to open
a scene file, refer to Operating Instructions <Basics>.)
1..
Press.<SAVE/LOAD>.to.select.[ND].
• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (load).
ND
M.GAIN
2..
Press.<UP>.or.<DOWN>.to.select.a.file.number.on.the.
memory.card.and.press.<EXECUTE>.to.confirm.the.
selection.
ND
M.GAIN
To save a file to file no. 2 on the memory card
3.. Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
• Do not remove a memory card that is being accessed.
ND
M.GAIN
• To cancel saving, select [n] and press <EXECUTE>.
• The file is saved to the memory card and [Fin] appears when saving
ends.
• [E02] is displayed if the save operation to the memory card fails.
(→page 20)
If this happens, check the memory card and try again or insert
another memory card to perform the operation again.
• [E01] is displayed when a scene file with the same name as the one
you are attempting to save already exists on the memory card.
To overwrite the file, press <UP> or <DOWN> to select [y] and
press <EXECUTE>.(→page 20)
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
2-2.Load.scene.file.from.memory.card
Scene file data loaded from the memory card is returned to the
operating status. (It is not returned to scene files 1 to 4. To return the
data to scene files 1 to 4, exit setup mode and store the data in one of
scene files 1 to 4. For details, refer to <Basics>, the instruction manual.)
1..
Press.<SAVE/LOAD>.to.select.[CC].
• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (load).
ND
M.GAIN
CC SHT SYNC
M.PED
IRIS
CC SHT SYNC
M.PED
IRIS
CC SHT SYNC
M.PED
IRIS
CC SHT SYNC
M.PED
IRIS