Setup.mode.operations; Set Camera Number; Save Scene File To/Load Scene File From Memory Card - Panasonic AK-HRP200G Operating Instructions Manual

Setup.Mode.Operations

<Note>
Menu numbers 10 to 15 are for future use.
1..Set.camera.number
1..
Open.setup.mode.and.check.that.menu.number.[1].is.
displayed..If.a.menu.number.other.than.[1].appears,.
press.<SELECT>.to.select.menu.number.[1].
Press to select the camera number
UP
ND CC
M.GAIN
DATA
SET
IRIS
DOWN
DISPLAY SELECT
SET UP ND/CC M.GAIN/M.PED SHUTTER
SHIFT
+
SAVE/LOAD EXIT
UP+DOWN
Press to exit setup mode
(hold down)
Press to confirm the camera number
2..
Press.<UP>.or.<DOWN>.to.select.a.camera.number.and.
press.<EXECUTE>.to.confirm.the.selection.
ND
M.GAIN
To select camera number 2
• Camera numbers become available after exiting setup mode.
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
2..Save.scene.file.to/load.scene.file.from.memory.card
Current operating status data is saved as a scene file to the memory
card.
Press.<SELECT>to.select.menu.number.[2].
Select file number,
Save file indication
Select y (Select)/
Load file indication
n (Cancel)
UP
ND ND
M.GAIN
DATA
SET
DOWN DISPLAY SELECT
SET UP ND/CC M.GAIN/M.PED SHUTTER
SHIFT
+
SAVE/LOAD
UP+DOWN
Press to save/load
Press to exit setup mode
(hold down)
2-1.Save.scene.file.to.memory.card
1.. Press.<SAVE/LOAD>.to.select.[ND].
• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (load).
ND
M.GAIN
CAMERA
SHT SYNC
M.PED 10-19
No.
SELECT
EXECUTE
Press to select the
menu number
CC SHT SYNC
M.PED
IRIS
CAMERA
CC CC SHT SYNC
M.PED 10-19
No.
IRIS
SELECT
EXIT EXECUTE
Press to confirm
Press to select the
menu number
CC SHT SYNC
M.PED
IRIS
2..
Press.<UP>.or.<DOWN>.to.select.a.file.number.on.the.
memory.card.and.press.<EXECUTE>.to.confirm.the.
selection.
ND
M.GAIN
To save a file to file no. 2 on the memory card
3..
Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
• Do not remove a memory card that is being accessed.
ND
M.GAIN
• To cancel saving, select [n] and press <EXECUTE>.
• The file is saved to the memory card and [Fin] appears when saving
ends.
• [E02] is displayed if the save operation to the memory card fails.
(→page 13)
If this happens, check the memory card and try again or insert
another memory card to perform the operation again.
• [E01] is displayed when a scene file with the same name as the one
you are attempting to save already exists on the memory card.
To overwrite the file, press <UP> or <DOWN> to select [y] and
press <EXECUTE>.(→page 13)
• To exit setup mode, hold down <EXIT> for about 2 seconds.
• To make other settings, press <SELECT> to select a menu number.
2-2.Load.scene.file.from.memory.card
Scene file data loaded from the memory card is returned to the
operating status. (It is not returned to scene files 1 to 4. To return the
data to scene files 1 to 4, exit setup mode and store the data in one
of scene files 1 to 4. For details, refer to <Operations>, the instruction
manual.)
1..
Press.<SAVE/LOAD>.to.select.[CC].
• Each press of <SAVE/LOAD> toggles between [ND] (Save) and
[CC] (load).
ND
M.GAIN
2..
Press.<UP>.or.<DOWN>.to.select.a.file.number.on.the.
memory.card.and.press.<EXECUTE>.to.confirm.the.
selection.
ND CC CC
M.GAIN
To load file no. 2 from the memory card
3.. Press.<UP>.or.<DOWN>.to.select.[y].and.press.
<EXECUTE>.to.confirm.the.selection.
• Do not remove a memory card that is being accessed.
ND
M.GAIN
CC SHT SYNC
M.PED
IRIS
CC SHT SYNC
M.PED
IRIS
CC SHT SYNC
M.PED
IRIS
SHT SYNC
M.PED
IRIS
CC SHT SYNC
M.PED
IRIS
7