Playback Operation - Sony PDW-R1 Operation Manual

3
If you selected "VAR" in step 2, set the parameter
value by holding down the corresponding button and
rotating the jog dial, while viewing the video.
Setting values vary with the rotation speed of the jog
dial.
4
Repeat steps 2 and 3 as required to set other
parameters.
5
Press the STATUS button to return to the normal
screen.

4-2-2 Playback Operation

This section describes the following types of playback:
• Normal playback
Playback at normal (±1) speed
• Playback in jog mode
Variable speed playback, with the speed determined by
the speed of turning the jog dial
• Playback in shuttle mode
Variable speed playback, with the speed determined by
the angular position of the shuttle dial
Normal playback
First insert a disc.
For details of how to insert a disc, see 3-6-4 "Loading and
Unloading a Disc" on page 38.
SUB
KEY INHI TC COUNTER
CLIP
ON SEL HOLD
INT PRESET F-RUN
NETWORK
LOCAL EXT
ACCESS REMOTE RP188 REGEN R-RUN
OFF
CLIP
MENU
ALL/CH-1 CH-2 CH-3 CH-4
METER MONITOR
VARIABLE MENU
SEL SEL
REC
PRESET
PB
L/ST/R
SYSTEM
AUDIO
MENU
PREV PLAY NEXT STOP REC
IN
TOP F REV F FWD END
STOP button
NEXT button
PLAY button
PREV button
To start playback
Press the PLAY button.
Playback starts.
When two or more clips are recorded on the disc, they are
played back continuously.
Note
No audio is output when non-audio signals are played
back.
SHUTTLE JOG
THUMB
NAIL SHIFT
ESSENCE
MARK
SET RESET
S.SEL
MARK1
OUT
MARK2
Shuttle dial Jog dial
F
/MARK1 button and
f
/MARK2 button
To jump to the next or previous clip, then start
playback
Use the PREV button, NEXT button, jog dial, or shuttle
dial.
For information about the functions of these buttons, see
"5 Recording and playback control section" on page 16.
For details of the jog and shuttle dials, see "3 Jog/shuttle
control block" on page 14.
To stop playback
Press the STOP button.
If you play back to the end of the last clip
Playback automatically stops.
If, in this state, you press the PLAY button, the message
"ALARM DISC END." appears on the monitor.
To carry out playback again, move back to the desired clip
using the PREV button, jog dial or shuttle dial.
To record an essence mark
While playing back a disc, you can record essence marks
such as shot mark 1 and shot mark 2 in desired frames.
To record a shot mark 1 or shot mark 2, hold down the F/
MARK1 or f/MARK2 button and press the SET button.
Note
To erase or change essence marks, use the supplied
PDZ-1 Proxy Browsing Software.
Playback in jog mode
In jog mode, you can control the speed of playback by the
speed of turning the jog dial. The playback speed range is
±1 times normal speed.
To carry out playback in jog mode, proceed as follows.
SUB
KEY INHI TC COUNTER
CLIP
ON SEL HOLD
INT PRESET F-RUN
NETWORK
LOCAL EXT
ACCESS REMOTE RP188 REGEN R-RUN
OFF
CLIP
MENU
ALL/CH-1 CH-2 CH-3 CH-4
METER MONITOR
VARIABLE MENU
SEL SEL
REC
PRESET
PB
L/ST/R
SYSTEM
AUDIO
MENU
PREV PLAY NEXT STOP REC
IN
F REV F FWD
TOP END
1
Press the JOG button, turning it on.
2
Turn the jog dial in the desired direction, at the speed
corresponding to the desired playback speed.
Playback in jog mode starts.
3
To stop playback in jog mode, stop turning the jog dial.
When extended menu item 101 "SELECTION FOR
SEARCH DIAL ENABLE" is set to "dial" (factory default
1 2,3
SHUTTLE JOG
THUMB
NAIL SHIFT
ESSENCE
MARK
SET RESET
S.SEL
MARK1
OUT
MARK2
4-2 Playback
51