Sony PDW-R1 Operation Manual page 45

Time data display
DATA DATA DATA DATA
dB OVER dB OVER dB OVER dB OVER VITC VIUB COUNTER HOLD VITC
0 0 0 0
PB NDF EXT-LK
-12 -12 -12 -12
-20 -20 -20 -20
-30 -30 -30 -30 HOURS MINUTES SECONDS FRAMES
-40 -40 -40 -40
-60 -60 -60 -60 DISC E B
CH- 15 CH- 26 CH- 37 CH- 48 BATT E F
PROCESS
AUDIO VIDEO CONTROL
INPUT CH INPUT SEL INPUT SEL STATUS CHARACTER LIGHT MONITOR
WARNING KEY INHI REC INHI
OFF ON OFF ON OFF L H
1 2
KEY INHI TC COUNTER
ON SEL HOLD
INT PRESET F-RUN
NETWORK
LOCAL EXT
ACCESS REMOTE RP188 REGEN R-RUN
OFF
ALL/CH-1 CH-2 CH-3 CH-4
METER MONITOR
VARIABLE
SEL SEL
REC
PRESET
PB
L/ST/R
AUDIO
PREV PLAY NEXT STOP REC
TOP F REV F FWD END
1
Watching the indicators above the time data display,
press the COUNTER SEL button to select TC.
2
Press the HOLD button.
The SHUTTLE button lights and the first two digits of
the time code shown in the time data display start
flashing.
To set all digits to 0
Press the RESET button.
3
Select the digits to set by rotating the shuttle dial or jog
dial.
The flashing digits change to the next two digits on the
right when you rotate the shuttle dial or jog dial
clockwise, and to the next two digits on the left when
you rotate it counterclockwise.
4
Set the value for the flashing digits by rotating the
shuttle dial or jog dial while holding the SHUTTLE
button.
5
Repeat steps 3 and 4 until you finish setting all digits.
6
Press the SET button.
• An initial time code value is set and the monitor
returns to the time code display before the HOLD
button was pressed in step 2.
4
SHUTTLE button
SHUTTLE JOG
SUB THUMB
CLIP NAIL SHIFT
CLIP
ESSENCE
MENU
MARK
MENU SET RESET
SYSTEM S.SEL
MENU
MARK1
IN OUT
MARK2
6 3,4
RESET button
• If the F-RUN/R-RUN switch is set to F-RUN, the
time code starts advancing from the initial value
immediately.
To set time code to the time of the internal clock
You can record time code synchronized to the time of the
internal clock.
To do so, set the INT/EXT/RP188 switch to INT, set the
PRESET/REGEN switch to PRESET, and then proceed as
follows.
1
Carry out steps 1 and 2 of the previous section, "To
record time code after setting an initial value."
2
With the SHUTTLE button held down, rotate the jog
dial in the counterclockwise direction. Stop rotating
when "CLOCK" appears in the time data display and
the video panel.
3
Press the SET button.
To set user bits
You can record up to eight hexadecimal digits of
information (date, time, clip name, etc.) in the time code
track.
Proceed as follows.
Time data display
DATA DATA DATA DATA
VITC VIUB COUNTER HOLD VITC
dB OVER dB OVER dB OVER dB OVER
0 0 0 0
PB NDF EXT-LK
-12 -12 -12 -12
-20 -20 -20 -20
HOURS MINUTES SECONDS FRAMES
-30 -30 -30 -30
-40 -40 -40 -40
-60 -60 -60 -60 DISC E B
BATT E F
CH- 15 CH- 26 CH- 37 CH- 48
PROCESS
AUDIO CONTROL
VIDEO
INPUT CH INPUT SEL INPUT SEL STATUS CHARACTER LIGHT MONITOR
WARNING KEY INHI REC INHI
OFF ON OFF ON OFF L
1
KEY INHI TC COUNTER
ON SEL HOLD
NETWORK INT PRESET F-RUN
LOCAL EXT
ACCESS REMOTE
RP188 REGEN R-RUN
OFF
ALL/CH-1 CH-2 CH-3 CH-4
METER MONITOR
VARIABLE
SEL SEL
REC
PRESET
PB
L/ST/R
AUDIO
PREV PLAY NEXT STOP REC
TOP F REV F FWD END
1
Watching the indicators above the time data display,
press the COUNTER SEL button to select UB.
2
Carry out steps 2 to 6 of the section "To set an initial
value" (page 44).
Settings are made in hexadecimal (0, 1, 2,... 8, 9, A,
B,... E, F).
H
SHUTTLE JOG
SUB THUMB
SHIFT
CLIP NAIL
CLIP ESSENCE
MENU
MARK
MENU SET RESET
SYSTEM S.SEL
MENU
MARK1
IN OUT
MARK2
4-1 Recording
45