Rear Panel - Sony PDW-HD1500 Operation Manual

Rear Panel

1 Power supply section (see
page 22)
2 Analog audio signal input/
output section (see
page 22)
3 Digital audio signal input/
output section (see
page 23)
(i.LINK) S400 connector
1
2 VIDEO CONTROL connector
3 REMOTE(9P) connector
a
(i.LINK) S400 connector (6-pin, IEEE1394
compliant)
Connect a computer, or similar, using an i.LINK cable.
Notes
• When this unit is connected to a device with a 6-pin
i.LINK connector by an i.LINK cable, before
unplugging the i.LINK cable, first power off the device
and disconnect the power plug from the outlet. If the
i.LINK cable is unplugged with the device power plug
still connected, a current from an excessive voltage (8 to
40 V) output from the i.LINK connector of the device
flows into this unit. This may cause a failure of the unit.
• When connecting this unit to a device with a 6-pin
i.LINK connector, connect to the 6-pin i.LINK
connector of the other device first.
b VIDEO CONTROL connector (D-sub-9-pin)
Connect an HKDV-900 video control unit.
c REMOTE(9P) (remote control 9-pin) connector
(D-sub 9-pin)
To control this unit from a controller or VTR supporting
the RS-422A Sony 9-pin VTR protocol, connect the device
to this connector.
d DC IN 12V connector (XLR 4-pin, male)
Connect to a DC power source of 12 V.
When using the BKP-L551 Battery Adaptor to mount a
battery pack, connect the power cable of the BKP-L551.
For details, see "Supplying power" on page 24.
POWER AC IN
ANALOG AUDIO INPUT
ANALOG AUDIO OUTPUT
1 2 1 2
DIGITAL AUDIO (AES/EBU) HDSDI INPUT HDSDI OUTPUT
IN 1/2 3/4 1 2
(SUPER)
OUT
SDSDI OUTPUT
1 2
(SUPER)
1/2 3/4
VIDEO CONTROL REMOTE(9P)
S400
DC IN 12V =
REMOTE
AUDIO MONITOR
R L
COMPOSITE OUTPUT REF.VIDEO INPUT
1 2 (SUPER) IN
TIME CODE
MAINTENANCE
IN OUT
e REMOTE connector (4-pin)
Supplies power to the RM-280 Editing Controller.
f COMPOSITE OUTPUT 1, 2 (SUPER) (analog
composite video output 1, 2 (superimpose))
connectors (BNC type)
Output analog composite video signals. You can
superimpose timecodes, menu settings, or error messages
on the output of the 2 (SUPER) connector when CHAR
SEL on the HOME page of the function menu is set to ON.
See "Basic Operations of the Function Menu" on page 39
for more information about the CHAR SEL setting.
g REF.VIDEO INPUT (reference video signal input)
connectors (BNC type)
The two connectors form a loop-through connection; when
a reference video signal is input to the left connector, the
same signal is input from the right connector (
connected device. When no connection is made to the right
connector, the left connector is automatically terminated
with an impedance of 75 ohms.
h
(network) connector (RJ-45 type)
This is a 10BASE-T/100BASE-TX/1000BASE-T
connector for network connection.
CAUTION
For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to this
port. Follow the instructions for this port.
4 DC IN 12V connector
5 REMOTE connector
4 HDSDI signal input/output
section (see page 23)
6 COMPOSITE OUTPUT1, 2
(SUPER) connectors
7 REF.VIDEO INPUT
connectors
5 Timecode input/output
section (see page 23)
(network) connector
8
9 MAINTENANCE connectors
0 SDSDI OUTPUT1, 2
(SUPER) connectors
) to a
Rear Panel
21