Sony PDW-HD1500 Operation Manual page 23

See "Basic Operations of the Function Menu" (page 39)
for more information.
3 Digital audio signal input/output section
1 DIGITAL AUDIO (AES/EBU) IN 1/2, 3/4
connectors
DIGITAL AUDIO (AES/EBU)
IN 1/2 3/4
OUT
1/2 3/4
2 DIGITAL AUDIO (AES/EBU) OUT 1/2, 3/4
connectors
a DIGITAL AUDIO (AES/EBU) IN (digital audio
input) 1/2, 3/4 connectors (BNC type)
These input AES/EBU format digital audio signals. The
left connector (1/2) corresponds to audio channels 1 and 2,
and the right connector (3/4) corresponds to audio
channels 3 and 4.
b DIGITAL AUDIO (AES/EBU) OUT (digital audio
output) 1/2, 3/4 connectors (BNC type)
These output AES/EBU format digital audio signals.
When the unit is shipped from the factory, the 1/2
connector is set to audio channel 1/2, and the 3/4 connector
is set to audio channel 3/4. You can change these settings
with setup menu item 827 AES/EBU AUDIO OUTPUT
SELECT (see page 105).
To treat the input and output signals of these connectors as
non-audio signals, set the maintenance menu item M37:
AUDIO CONFIG >M372: NON-AUDIO INPUT
(recording) (see page 108) and setup menu item 823 NON-
AUDIO FLAG PB (playback).
4 HDSDI signal input/output section
1 HDSDI INPUT connector
2 HDSDI OUTPUT 1, 2 (SUPER)
HDSDI INPUT
1
a HDSDI INPUT (HDSDI signal input) connector
(BNC type)
This inputs an HDSDI format video/audio signal.
b HDSDI OUTPUT 1, 2 (SUPER) (HDSDI signal
output 1, 2 (superimpose)) connectors (BNC type)
These output HDSDI format video/audio signals.
When editing with two PDW-HD1500 units, connect a
cable between these connectors on the player unit and the
HDSDI INPUT connector on the recorder unit.
connectors
HDSDI OUTPUT
2
(SUPER)
You can superimpose timecodes, menu settings, error
messages, or other information on the output of the HDSDI
OUTPUT 2 (SUPER) connector with the setting for
CHAR SEL on the HOME page of the function menu or
with the setting for setup menu item 028 HD
CHARACTER. You can always disable to superimpose
the data independent of the setting for CHAR SEL with the
setting for setup menu item 028.
See "Basic Operations of the Function Menu" (page 39)
for more information about the CHAR SEL settings.
See page 93 for more information about the setup menu
item 028 HD CHARACTER.
To treat the input and output signals of these connectors as
non-audio signals, set the maintenance menu item M37:
AUDIO CONFIG >M372: NON-AUDIO INPUT
(recording) (see page 108) and setup menu item 823 NON-
AUDIO FLAG PB (playback).
5 Timecode input/output section
1 TIME CODE IN connector
TIME CODE
IN
a TIME CODE IN connector (BNC type)
This inputs an SMPTE timecode generated by an external
device.
b TIME CODE OUT connector (BNC type)
This outputs the following timecode, depending on the
operating state of this unit.
During playback: Playback timecode
During recording: The timecode from the internal
timecode generator or the timecode input to the TIME
CODE IN connector
When setup menu item 611 TC OUTPUT PHASE IN EE
MODE is set to "muting", no timecode is output.
2 TIME CODE OUT
connector
OUT
Rear Panel
23