Related Manuals for Hy-Brid Lifts HB-P3.6
Summary of Contents for Hy-Brid Lifts HB-P3.6
- Page 1 BY CU STO M EQUIPMENT LLC OPERATIONS & SAFETY MANUAL SUPO-725 PUSH AROUND AERIAL WORK PLATFORM REV C HB-P3.6 SERIES I...
-
Page 2: Notes
NOTES If there is a question about application and/or operation, contact: Custom Equipment, LLC 2647 Hwy 175 Richfield, WI 53076 U.S.A. P: +1-262-644-1300 F: +1-262-644-1320 www.hybridlifts.com BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C... -
Page 3: Foreword
Lanyard Attachment Point WARNING USE OF FALL ARREST SYSTEMS ATTACHED TO ANCHORAGE POINTS ON EQUIPMENT MAY CAUSE MACHINE TO TIP, RESULTING IN SERIOUS INJURY OR DEATH. BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C... -
Page 4: Table Of Contents
5.5 | DAILY MAINTENANCE ................................24 5.6 | CHARGING THE BATTERY ...............................25 5.7 | BATTERY DISPLAYS..................................26 SECTION 6 | PRE-START INSPECTION CHECKLIST ......................27 6.1 | PRE-START INSPECTION CHECKLIST ........................... 27 BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C... -
Page 5: Index Of Figures
FIGURE 10: Master Power Switch On ...............................22 FIGURE 11: Check bubble levels and manually engage brakes ....................23 FIGURE 12: Key Removed ..................................24 FIGURE 13: Padlock ....................................24 FIGURE 14: Battery Charger LED Display ............................26 BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C... -
Page 6: Section 1 | Product Description
2006/42/EEC Annex VII, as listed in Article 12 and Annex IV, item 17 of directive 2006/42/EEC, which excludes devices with a platform height of less than three meters. Model Numbers: HB-P3.6 Machine Type: Mobile Elevating Work Platform Applicable Harmonised Standard: EN280:2001 + A2:2009 MANUFACTURER Custom Equipment, LLC. -
Page 7: Machine Specifications
650 psi 4482 kPa Hydraulic Fluid Capacity 1.69 quarts 1.6 L Power System-Voltage 12V DC 12V DC Batteries-Deep Cycle Marine 12V, Group 24 AGM 12V, Group 24 AGM BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C... -
Page 8: Section 2 | Safety
WARNING NEVER REACH BETWEEN SCISSORS LINKS OR PROP UP PLATFORM. CAUTION WHEELS EXTENDING BEYOND THE SIDES OF THE BASE MAY OCCUR IN TIGHT TURNING SITUATIONS. BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C... -
Page 9: Safety Features
Elevate the platform higher before lowering, or use the manual override in case of emergency. Descent / Motion Alarm An audible alarm sounds when the machine is lowering. BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C... -
Page 10: Safety Controls
PUSHING THE EMERGENCY STOP BUTTON WILL APPLY BRAKES IMMEDIATELY. THIS MAY CAUSE UNEXPECTED PLATFORM MOVEMENT AS THE MACHINE COMES TO A SUDDEN STOP. BRACE YOURSELF AND SECURE OBJECTS ON THE PLATFORM DURING OPERATION OF THE MACHINE. BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C... -
Page 11: Maintenance Lock
Follow local power line clearance regulations. • You must maintain a clearance between any part of the machine, or its load, and any electrical line or apparatus. Follow local power line clearance regulations. BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C... - Page 12 Make sure platform rails and pins are secured. • Operator shall use the maintenance lock when performing all types of maintenance procedures. • Do not smoke while charging the battery. BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C...
- Page 13 THIS PAGE IS INTENTIONALLY LEFT BLANK BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C...
-
Page 14: Section 3 | Decals
SECTION 3 | DECALS 3.1 | DECAL LOCATIONS FIGURE 5: Decal Locations BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C... -
Page 15: Decal Meaning Or Designation
Qty Superseded By 143-21-006-51-K DECALS,HB-P3.6 DECAL SET DE674 DECAL,HYDR FLUID DE673 DECAL,HYDR FLUID DE727 DECAL,KEEP DE728 DECAL,CLEAR DE600E-14 DECAL,MAINT LOCK DE600E-24F DECAL,WHEEL LOAD HB-P3.6 DE600E-29 DECAL,E-DOWN DE751 SUPERSEDED; DE751 DECAL,E-DOWN CABLE DE601 DECAL,LOGO HY-BRID DE821 SUPERSEDED; DE603-5 MODEL# DECAL-HB-P3.6 DE821 DECAL,LOGO HY-BRID... -
Page 16: Decal Symbols
Batteries produce explosive gas. Only charge batteries in a well- ventilated area. • Do not expose to sparks or fl ames. • Do not smoke while charging battery. • Battery Charger Cord BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C... - Page 17 You must maintain a clearance between any part of this machine or its load and any electrical apparatus. Follow local power line regulations. • Death or serious injury will result from contact or inadequate clearance. BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C...
- Page 18 Lanyard anchorage points are for work positioning restraints only, not for fall protection. • Use of fall arrest systems attached to anchorage points on mobile equipment may cause machine to tip, resulting in serious injury or death. BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C...
- Page 19 THIS PAGE IS INTENTIONALLY LEFT BLANK BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C...
-
Page 20: Section 4 | Transport, Handling & Storage
Tie-down points are provided in the front and rear of the machine for securing the machine on a trailer or truck bed for transport between places of use. They may also be used as lift points. FIGURE 6: Tie-Down Points BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C... -
Page 21: Fork Lift Pockets
When moving machine with a forklift, do not let machine slide along floor. Bring forklift to a stop and then gently lower the machine. Center of Gravity Center of Gravity X Axis Y Axis HB-P3.6 54.7 cm 38.3 cm FIGURE 8: Center of Gravity BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6... -
Page 22: Section 5 | Operation
Check that bubble level is centered • Engage the manual breaks on the rear casters before elevating the platform FIGURE 10: Master Power Switch On BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C... -
Page 23: Figure 11: Check Bubble Levels And Manually Engage Brakes
Brakes • Follow all general rules and precautions stated in this manual. FIGURE 11: Check bubble levels and manually engage brakes BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C... -
Page 24: Shut Down
In addition, Pre-Delivery/Frequent and Monthly Checklists are included in a separate Maintenance Manual. Also refer to the Maintenance Manual for replacement part information. BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C... -
Page 25: Charging The Battery
The charger will not begin the charging cycle on severely discharged batteries. WARNING CAUTION DO NOT OPERATE UNITE WHILE NEVER ADD ACID TO THE CHARGING BATTERY BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C... -
Page 26: Battery Displays
This display indicates that power is on and that the output is finished POWER charging and is in a float maintenance model. CHARGING READY Green LED Red LED Green LED (ON) (OFF) (ON) BY CUSTO M EQUIPMENT LLC OPERATIONS & SAFETY SUPO-725 HB-P3.6 REV C... -
Page 27: Section 6 | Pre-Start Inspection Checklist
THIS CHECKLIST MUST BE USED AT THE BEGINNING OF EACH SHIFT OR WARNING AFTER EVERY SIX TO EIGHT HOURS OF USE. FAILURE TO DO SO COULD AFFECT THE SAFETY OF THE OPERATOR. MODEL NUMBER: HB-P3.6 SERIAL NUMBER: • Keep inspection records up-to-date. - Page 28 © 2018 Custom Equipment, LLC 2647 Highway 175 Richfield, WI 53076 U.S.A. Tel. +1-262-644-1300 Fax: +1-262-644-1320 www.hybridlifts.com Service@Customequipmentlifts.com “Hy-Brid Lifts” is a trademark of Custom Equipment, LLC. These machines comply with EN 280 requirements Revision Date: October 2018 Printed In The USA...
Need help?
Do you have a question about the HB-P3.6 and is the answer not in the manual?
Questions and answers