Sony XDCAM PDW-510 Operation Manual page 126

ASSIGN SW1 <3/4> SEL window
ASSIGN SW1 SEL ESC
OFF
PICTURE CACHE ON/OFF
TEST OUT CHARACTER
MARKER
RE-TAKE
ATW
RETURN VIDEO
LENS RET
REC SWITCH
TURBO SWITCH
ASSIGN SW2 SEL window
ASSIGN SW2 SEL ESC
OFF
PICTURE CACHE ON/OFF
TEST OUT CHARACTER
MARKER
ZEBRA
FREEZE MIX
FREEZE MIX(Manual)
D5600
EXT REC CONTROL
Functions to be assigned to the ASSIGN 1/3/4
(push-type) switch
Function Description
OFF Disables the switch.
CACHE Assigns execution of recording in picture
cache mode.
TEST OUT Assigns the function to switch whether or
CHARACTER not text is superimposed on the video
signal to be output from the TEST OUT
connector.
MARKER Assigns the ON/OFF function to display
all markers.
RETAKE Assigns the function to delete the last
recorded clip.
ATW Assigns the ON/OFF function of auto-
tracing white balance.
RETURN VIDEO Assigns the ON/OFF function to display
the image of the return video signal on
the viewfinder to the switch.
LENS RET Assigns the same function as that of the
RET switch on the lens to the switch.
REC SWITCH Assigns the VTR S/S (start/stop) function
to the switch.
TURBO Assigns the turbo gain function to the
SWITCH switch.
ZEBRA Assigns the zebra pattern display
function to the switch.
FREEZE MIX Outputs the freeze image and camera
input alternately, to allow frame alignment
(automatic switching).
FREEZE MIX Outputs the freeze image and camera
(Manual) input alternately, to allow frame alignment
(manual switching).
D5600 Applies an electrical 5600 K filter.
ZOOM TELE/ When using a serial lens, assign the
3) ZOOM TELE setting to ASSIGN 3, and
WIDE
the WIDE setting to ASSIGN 4.
126
7-3 Adjustments and Settings from Menus
1)
2)
Function Description
ZOOM WIDE/ When using a serial lens, assign the
3) ZOOM WIDE setting to ASSIGN 3, and
TELE
the TELE setting to ASSIGN 4.
SHOT MARK1 Assigns the function to record a SHOT
MARK 1 essence mark.
SHOT MARK2 Assigns the function to record a SHOT
MARK 2 essence mark.
4) Assigns the items assigned in the
UA01 to UA10
ASSIGN SEL menu.
1) Even when the MARKER item is set to "OFF" on the MARKER page of
the USER menu, the ASSIGN 1/3/4 switch allows you to display or not to
display all markers.
2) Even if the RETURN VIDEO item is set to "OFF" on the GENLOCK page
of the MAINTENANCE menu, you can use this switch to display the
image of the return video signal on the viewfinder.
3) Only the Assign 3SEL and Assign 4 SEL screens appear.
4) This does not appear if nothing is assigned in the Assign menu.
Functions to be assigned to the ASSIGN 2 (slide-
type) switch
Function Content
OFF Disables the switch.
CACHE Assigns execution of recording in picture
cache mode.
TEST OUT Assigns the function to switch whether or
CHARACTER not the characters are mixed to the video
signal to be output from the TEST OUT
connector.
MARKER Assigns the ON/OFF function to display
all markers.
ZEBRA Assigns the zebra pattern display
function to the switch.
D5600 Applies an electrical 5600 K filter.
EXT REC Selects whether or not recording control
CONTROL of external devices connected through
the i.LINK connector or the CCZ
connector (26-pin) of a CA-702 is
possible.
REC VIDEO Selects which signals you will record
2) pictures being shot by the camcorder or
SOURCE
video signals from external equipment
connected to GENLOCK IN connector.
3) Assigns the items assigned in the
UA01 to UA10
ASSIGN SEL menu.
1) Even when the MARKER item is set to "OFF" on the MARKER page of
the USER menu, the ASSIGN 2 switch allows you to display or not to
display all markers.
2) When the CBK-SC01 is not installed, this item does not appears since this
function is not effective.
3) This does not appear if nothing is assigned in the Assign menu.
Note
For functions that are assigned to the ASSIGN 2
switch, you cannot change those settings using other
menus. The function assigned to ASSIGN 2 switch
takes precedence over the menu setting.
1)