Confirming The Image Of The Return Video Signal In The Viewfinder - Sony XDCAM PDW-510 Operation Manual

Professional disc camcorder
Hide thumbs Also See for XDCAM PDW-510:
Table of Contents

Advertisement

The b mark on the left of the selected item changes to
a z mark and the z mark on the left of the setting
changes to a ? mark.
4
Turn the MENU knob to select whether or not to
display the selected window, then press the MENU
knob.
The z mark changes to a b mark and the ? mark
changes to a z mark.
5
To continue setting other windows, repeat steps 3 and
4.
6
To end the menu operation, set the MENU ON/OFF
switch to OFF or close the cover of the menu operating
section.
7-2-9 Confirming the Image of the
Return Video Signal in the
Viewfinder
You can set whether or not the image of the return video
signal input to the GENLOCK IN connector is displayed in
the viewfinder, using the GENLOCK page of the
MAINTENANCE menu.
Proceed as follows.
1
Set the MENU ON/OFF switch to ON while holding
down the MENU knob.
The TOP menu appears.
2
Turn the MENU knob to move the b mark to
“MAINTENANCE”, then press the MENU knob.
If this is the first time the MAINTENANCE menu has
been displayed, the CONTENTS page of the
MAINTENANCE menu appears.
If the menu has been used before, the last accessed
page appears.
3
If the CONTENTS page is displayed, turn the MENU
knob to move the b mark to “GENLOCK”, then press
the MENU knob to display the GENLOCK page.
If a different page is displayed, turn the MENU knob
until the GENLOCK page appears, then press the
MENU knob to select the page.
M15 GENLOCK
TOP
GENLOCK
:
ON
RETURN VIDEO
:
OFF
GL H PHASE
:
0
GL SC PHASE
:
0
GL SC 0/180 SEL :
180
4
Carry out setting operations as follows.
1 Turn the MENU knob to move the b mark to
“GENLOCK”, and press the MENU knob.
The b mark on the left of “GENLOCK” changes to
a z mark and the z mark on the left of the
GENLOCK setting changes to a ? mark.
2 Turn the MENU knob until ”OFF” appears, then
press the MENU knob.
The z mark changes to a b mark and the ? mark
changes to a z mark, and the setting is executed.
3 Turn the MENU knob to move the b mark to
“RETURN VIDEO”, and press the MENU knob.
The b mark changes to a z mark and the z mark
changes to a ? mark.
4 Turn the MENU knob until “ON” appears, then
press the MENU knob.
The z mark changes to a b mark and the ? mark
changes to a z mark, and the setting is executed.
5
To end the menu operation, set the MENU ON/OFF
switch to OFF or close the cover of the menu operating
section.
To see the image of the return video signal
on the viewfinder screen
Hold down the RET switch on the lens. The image of the
return video signal input to the GENLOCK IN connector
is displayed on the viewfinder screen while you are
holding down the RET switch.
When the return video function is assigned to the ASSIGN
1/3/4 switch, you can see the image of the return video
signal on the viewfinder screen while you are holding
down the ASSIGN 1/3/4 switch even if the RETURN
VIDEO item is set to “OFF” on the GENLOCK page of the
MAINTENANCE menu.
Note
When no signal is input to the GENLOCK IN connector,
the image is not changed even if you hold down the RET
switch on the lens.
However, the image is switched while you are holding
down the ASSIGN 1/3/4 switch to which the return video
function is assigned, even if no signal is input to the
GENLOCK IN connector.
Page 121

Advertisement

Table of Contents
loading

This manual is also suitable for:

Pdw-510wXdcam pdw-530Xdcam pdw-530pXdcam pdw-510p

Table of Contents