Table of Contents
Advertisement
Quick Links
KS150/190/215-KH Installation Guide
• One 15", 19", or 21.5" Modular Touch Panel PC
• 3-pin Terminal Blcok Connector
• SATA, Mini PCIe and M.2 Installation Screws
DFI reserves the right to change the specifications at any time prior to the
product's release. For the latest revision and more details of the installation
procedure, please refer to the user's manual on the website.
Package Contents
www.dfi.com
1
Advertisement
Table of Contents
Related Manuals for DFI KS190-KH
Summary of Contents for DFI KS190-KH
-
Page 1: Package Contents
• 3-pin Terminal Blcok Connector • SATA, Mini PCIe and M.2 Installation Screws DFI reserves the right to change the specifications at any time prior to the product's release. For the latest revision and more details of the installation procedure, please refer to the user's manual on the website. - Page 2 Panel Bottom View Power Button Status LED (Orange) HDD LED (Red) COM 1 COM 2 COM 4 COM 3 Extended Power Reset Button on/off Switch USB 2.0 Top View DVI-D (DVI-I connector) DC-in USB 3.0 HDMI LAN 1 LAN 2 Front OSD Functions (only for models with front OSD) Power HDD Alarm LED Backlight or Power...
-
Page 3: Removing The Chassis Cover
Removing the Chassis Cover 1. Make sure the system and all other peripheral devices connected to it have been powered-off. 2. Disconnect all power cords and cables. 3. The 6 mounting screws on the rear side of the system are used to secure the cover to the chassis. -
Page 4: Installing A Sata Drive
Installing a SATA Drive The system can accommodate one SATA drive. Please use the following procedure to install a SATA drive in the system. 1. Before installing the SATA drive, connect the SATA data/power cable to the SATA data connector of the SATA drive. Then install the SATA drive onto the HDD bracket with the provided mounting screws. - Page 5 3. Connect the other end of the SATA data/power cable to the SATA data and power connectors on the system board respectively. SATA power connector SATA data connector...
-
Page 6: Installing A Sodimm
Installing a SODIMM The system supports two DDR4 SODIMM socket. To install a memory mod- ule, grasp the memory module by its edges and align the module’s notch with the socket’s notch; then insert the memory into the socket at an angle and push it down until you feel a click. -
Page 7: Installing An M.2 Card
Installing an M.2 Card The onboard M.2 Type 2280 connector (M Key) supports PCIe NVMe modules up to PCIe Gen 3.0 x4 bandwidth. Note that only SKUs with Intel ® QM175 Chipset support M.2 socket. To install an M.2 card, insert the bottom edge of the M.2 card into the connector, and then secure the card to the standoff with the provided mounting screw. - Page 8 Installing a Mini PCIe Card and a SIM Card The system board is equipped with 2 Mini PCIe slots with SIM card sockets to support a variety of wireless LAN and mobile broadband communication modules. Mini PCIe slot 1 provides both USB and PCIe interfaces whereas Mini PCIe slot 2 provides only USB interface.
-
Page 9: Installing A Sim Card
Installing a SIM Card Open the SIM card socket by pushing the white latch inward. Mini PCIE1 Mini PCIE2 Push the latch inward Push the latch outward to to open it close it Insert the SIM card into the slot. Please place the card with the IC facing down and the angled corner aligning with the socket's angled corner so it will be correctly in contact with the system board. - Page 10 Assemble the Modular Panel PC The modular panel PC comprises two parts: a box module and a panel module. 1. Take off the cover of the ADP connector. Hold the box module with its ADP connector (female) in line with the ADP connector (male) of the panel module.
- Page 11 3. Make sure that the box module seats on top of the panel module with the alignment post effortlessly sliping into the designated holes on the box module. Press to install these two modules and secure the installation with 8 mouting screws. Mounting Screw Alignment Post...
-
Page 12: Mounting Options
Mounting Options VESA mount The VESA-mount specifications for this device is 100 x 100 (mm). Please use a compatible VESA mount kit that can sustain the weight and size of this device. The VESA mount kit includes the following: • 2 VESA mount brackets •... - Page 13 4. The system has designed Attach the other bracket (VESA mount bracket 2) to the rear of the Panel PC. Thumb screw Hooks VESA mount bracket 2 Mounting screw 5. Slide the Panel PC to "wall mount bracket 1" to attach the two brackets with the hooks.
-
Page 14: Panel Mount
Panel mount The panel mounting kit includes the following: • 10 mounting clamps 1. Before starting any installation procedures, attach the poron foam to the Panel PC. 2. Select a place on the panel (or wall) where you will mount the Panel PC. 3. - Page 15 Mounting clamp Slit for mounting the clamp 6. The first and second clamps must be positioned and secured diagonally prior to mounting the rest of the clamps. Tighten the clamp’s screw using an electric screwdriver by pressing the flat cap onto the back of the panel.
-
Page 16: Communication Port Pin Assignments
Communication Port Pin Assignments The system is equipped with 4 COM ports that enable serial communication. The COM 1 and COM 2 ports can be switched between typical RS232 or RS232 with power on its Pin NO.1 (12V) and Pin No.9 (5V). COM 1 COM 2 COM 4... -
Page 17: Board Layout And Jumper Settings
Board Layout and Jumper Settings Clear CMOS System Data (JP1) Front Audio Fan 1 Front Panel PS/2 Power Select S/PDIF (JP4) (JP14) DIO Power Power Button Buzzer USB 2.0 DDR4_2 SODIMM USB 9 Power LED USB 2.0 HDD LED USB 13/14 COM 5 DDR4_1 SODIMM SPI Flash...