Table of Contents Introduction Special Features Warning and Safety Notes Program Flow Chart Explanation of Buttons Power and Battery Connection Charge Operation Lithium Battery Program (LiPo/LiFe/Lilon/LiHV) NiMH/NiCd Battery Program Pb Lead-acid Battery Program Battery Memory Set and Call Out System Setting Battery Voltage Meter Battery Resistance Meter Warning and Error Message...
Introduction Congratulations on your choice of SKYRC T200 AC/DC Dual Balance Charger/Discharger. This unit is simple to use, but the operation of a sophisticated automatic charger such as SKYRC T200 does require some knowledge on the part of the user. These operating instructions are designed to ensure that you quickly become familiar with its functions.
Page 4
See the Status of Individual Cells in Balance Charge Mode Balance Lead Socket Switch From Channel A to B or Output Socket Vice Versa Temperature Sensor Port Carrying Handle Smart Ventilation Fan DC Input 11-18V Ventilation Slot AC Input 100-240V · 02 T200...
All the settings can be configured by users. Voltage Calibration (for expert user only) SkyRC T200 allows you to calibrate the voltage directly on the device with a 6S LiPo battery. (For more information please contact us at support@skyrc.cn)
Page 6
If the temperature limit is reached, the process will be terminated. * This function is only available by connecting optional temperature probe, which is not included in the package. Processing Time Limit You can also limit the maximum process time to avoid any possible defect. · 04 T200...
3.0-3.3V/cell 2.9-3.2V/cell 2.6-2.9V/cell 3.1-3.4V/cell 0.1-1.1V/cell 0.1-1.1V/cell 1.8V/cell Voltage Be very careful to choose the correct voltage for different types of battery otherwise you may cause damage to the batteries. Incorrect settings could cause the cells to fire or explode. T200 05 ·...
Page 8
Always refer to the manual by battery manufacturer about charging methods, recommended charging current and charging time. Especially, the lithium battery should be charged according the charging instruction provided by the manufacturer strictly. · 06 T200...
Page 9
This is a memory effect. It is said that NiCd and NiMH batteries are suffering from memory effect. NiCd has more memory effect than NiMH. T200 07 ·...
Power and Battery Connection 1. Connecting to power source There are two kinds of inputs for SKYRC T200, DC 11-18V and AC 100-240V. AC 100-240V power source connection. 12V DC Battery / DC power supply connection. · 10 T200...
Page 13
In the other modes, there is no request to connect the balance wire to the balance socket in the charger. But we suggest to charge your battery in balance mode for better performance. 2) NiMH/NiCd or Pb Battery Connection NiMH T200 11 ·...
AGM CHG This mode is for charging AGM battery. This mode is for charging Pb battery in cold days when the temperature is COLD CHG 5 ℃ to -20 ℃. DISCHARGE This mode is for discharging Pb battery. · 12 T200...
INC and DEC to change the value and press START/ ENTER to confirm your setting. START/ENTER Program Start LiPo BALANCE 2.0A 11.1V (3S) Press and hold START/ENTER for 3 seconds to start the program. START/ENTER > 3 Seconds T200 13 ·...
Page 16
[ Time: 00: 45: 32 ] 16.8V 2600mAh elapsed time. Program Stop During the charging process, press STOP to stop the charging process. Please scan and watch the tutorial video about how to charge LiPo Video battery in balance mode. Tutorial · 14 T200...
Page 17
Temperature probe needs to be connected to show Int. Temp 37°C external temperature. Temp Cut-Off Cut-off temperature. Safety Timer Safety timer ON and duration of time in minutes. ON 200min Capacity Cut-Off Capacity cut-off ON and value of the set capacity limit. 5000mAh T200 15 ·...
Discharge, Re-Peak and Cycle. Selecting the Battery Type: After powering on the T200, press the INC or DEC button repeatedly until you reach the appropriate program for the battery type you wish to charge. For this example we have chosen the “NiMH BATT“ or “NiCd BATT” program. Now press the ENTER button to enter the desired program.
Page 19
Follow the instructions provided on your battery when setting the voltage cut-off. The T200 will stop discharging when the battery has reached the preset voltage cut-off. Press and hold the START button for 3 seconds to start NiMH 1.3A 10.42V...
Page 20
A five-minute cool-down delay occurs after each re- peak charge. IN RE-PEAK MODE, THE T200 USES THE CHARGE AMPERAGE AND VOLTAGE SETTINGS ENTERED IN CHARGE MODE. After selecting the correct battery type, use the INC or DEC NiMH RE-PEAK button to select the “RE-PEAK”...
Page 21
Pressing the START button again will cause the cycle count to begin flashing. Use the INC or DEC button to change this to the number of cycles you want the T200 to run. The T200 can cycle the battery a maximum of 5 times consecutively.
Pb Lead-acid Battery Program Additional NiMH/NiCd Process Information: During the NiMH/NiCd battery charging/discharging process the T200 can display a variety of information. Using the INC or DEC buttons, you can also view the following information: Delta Peak Voltage NiMH Sensitivity...
Page 23
Press the START button again and the nominal battery pack Pb COLD CHG voltage will begin flashing. Use the INC or DEC button to set 1.5A 12.0V(6P) the voltage and the number of cells. Press and hold the START button for 3 seconds to start charging. T200 21 ·...
Page 24
“FINISHED” and the charger will emit a ringing sound. Additional Pb Process Information: During the Pb battery charging/discharging process the T200 can display a variety of information. Using the INC or DEC buttons you can also view the following information:...
T V C = Y O U R R I S K Set the terminal voltage(4.18-4.25V). 4 . 2 0 V DEC INC S A V E P R O G R A M Press ENTER to save program. E N T E R START/ENTER T200 23 ·...
Page 26
L O A D L i P o B A L A N C E C H G Press START/ENTER for 3 seconds to start the process. 4 . 9 A 7 . 4 V ( 2 S ) · 24 T200...
Fahrenheit you like. A rest time allowing the battery to cool R e s t T i m e 1-60Min down between charging/discharging C H G > D C H G 1 0 M i n cycle. T200 25 ·...
Page 28
L o a d F a c t o r y S e t E n t e r setting. It indicates the hardware and firmware V e r s i o n H W : 1 . 0 0 F W : 1 . 1 0 version. · 26 T200...
The screen indicate each cell's resistance. 0 0 6 m Ω The screen indicate the total resistance, the highest T A T A L :2 8 mΩ resistance and the lowest resistance. H :1 2 mΩ L :5 mΩ · 28 T200...
B A T T E R Y W A S F U L L which the user sets when charging in balance mode. N O P O W E R No power allocate to the charger. D I S T R I B U T E D T200 29 ·...
Conformity Declaration SkyRC T200 satisfy all relevant and mandatory EC directives and FCC Part 15 Subpart B. Requirements for Household Appliances, electric EN 55014-1:2017 tools, and similar apparatus –Part 1: Emission Electromagnetic compatibility Requirements for Household Appliances, electric EN 55014-2:2015 tools, and similar apparatus –...
– Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC's RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. T200 33 ·...
13.2 volts (4x3.3). If the nominal voltage of the battery is not printed on the battery's label, consult your battery manufacturer or supplier. Do not guess the rated voltage of battery. · 34 T200...
Liability exclusion This charger is designed and approved exclusively for use with the types of battery stated in this Instruction Manual. SkyRC accepts no liability of any kind if the charger is used for any purpose other than that stated.
Page 38
Latest version can be downloaded from www.skyrc.com If you have any question about this document, please contact SkyRC by sending a message to info@skyrc.cn All Rights Reserved. All specifications and figures are subject to change without notice. Printed in China 2019.03...