Download Print this page
SaMASZ SAMBA 240 Assembly Instructions Manual

SaMASZ SAMBA 240 Assembly Instructions Manual

Hide thumbs Also See for SAMBA 240:

Advertisement

Quick Links

ASSEMBLY INSTRUCTIONS FOR
MOWERS SAMBA 240 / 280

Advertisement

loading
Need help?

Need help?

Do you have a question about the SAMBA 240 and is the answer not in the manual?

Questions and answers

Summary of Contents for SaMASZ SAMBA 240

  • Page 1 ASSEMBLY INSTRUCTIONS FOR MOWERS SAMBA 240 / 280...
  • Page 2: Machine Type

    MACHINE TYPE SAMBA Checklist Component A (fully mounted): Component B: Component C: 0671.04.01.004 Welded frame 1. with pawl 2 installed. Cutting unit – 0670.05.00.003 1. Front guard (fitted with plastic plugs and guard lock Carrying beam – 0670.02.00.002 pin) – 0670.04.02.003 Vertical axle –...
  • Page 3 Component H: Component I: Component J: Component K: - Safety device – 0670.03.00.002 - Shaft B&P 7GN066CE007096MA - Spring dia 10; dia 50; L= 625 (0671.01.060.004) - Blade replacement lever MIWB-066-000 Page 2 of 10...
  • Page 4 SAMBA MACHINE TYPE Action Figure / Photo / Other Assembly of Complete machine assembled from components A to K SAMBA mower 1. Set component A (cutting unit (1), carrying beam (2), vertical axle (3)) flat on the ground. Drum assembly to 2.
  • Page 5 SAMBA MACHINE TYPE Action Figure / Photo / Other Knife holder 1. Install knife holder on empty disc hub. 2. Install drum on knife holder. 3. Screw the drum using 4 bolts with washers to the hub. - bolt M10 x 25 cl. 8.8 zinc-pl. – 4 pcs - lock washer dia 10.2 zinc-pl.
  • Page 6 SAMBA MACHINE TYPE Action Figure / Photo / Other Fasten welded frame to transmission using 4 bolts with 4 washers. - bolt M12x 40 cl. 8.8 zinc-pl. – 4 pcs - lock washer dia 12.2 zinc-pl. – 4 pcs Before screwing the bolts, apply some blue assembly adhesive for better installation in the transmission.
  • Page 7 SAMBA MACHINE TYPE Action Figure / Photo / Other Spring, Fasten right guide to welded frame using: washer, - bolt M12x 90 cl. 8.8 zinc-pl. - spring dia 7 L= 67 (0260.04.08.000) - enlarged washer dia 12 (34) zinc-pl. - nut M12 cl. 8 zinc-pl. Bolt Rear barrier...
  • Page 8 SAMBA MACHINE TYPE Action Figure / Photo / Other Vertical axle Assemble the complete linkage component on vertical Assembly of axle. vertical axle to Secure the linkage against tilting and falling. the headstock Linkage 1. Install the safety device component on carrying beam. 2.
  • Page 9 SAMBA MACHINE TYPE Action Figure / Photo / Other Spacer dia 25 thickness 1mm Pawl pin Circlip Z-25 (at both To install cylinder screwed extension, first remove the pawl. sides) From pawl pin, remove 2 circlips Z-25; from the frame, remove the pin with spacers. On the welded frame, install the pawl, cylinder screwed extension, spacers (as shown), insert the pawl pin through details and the welded frame, protect at...
  • Page 10 SAMBA MACHINE TYPE Action Figure / Photo / Other 1. Insert hydraulic hose through two rings. 2. Insert EURO M14 x 1.5 plug into holder on the headstock. 1. Install lower swivel eye in corresponding point at the welded frame. 2.
  • Page 11 SAMBA MACHINE TYPE Action Figure / Photo / Other Splined shaft Install drive shaft onto transmission shaft (spline powering the pulleys). Push transmission shaft on spline until safety device is engaged. Drive shaft Install rubber guard on drive shaft (red Couple rubber guard with shaft casing using metal clip: - metal clip screwed 100 x 120 Place knife replacement lever on side wall of the linkage in...

This manual is also suitable for:

Samba 280