Siemens SIMATIC FM 452 Manual page 202

Index
Cam data error, C-21
Cam data in the parameter DB, 8-27
Cam deactivation, condition, 2-3
Cam end, 8-28
Cam parameter change, 9-13
Cam start, 8-28
Cam types, 2-2
CAM_END, 9-11
CAM_NO, 9-11, 9-13
CAM_OFF, 9-13
CAM_START, 9-11
CAM_TYPE, 8-27
Cams, 2-2
CAMVALID, 8-27
CAMxRD_EN, 8-4
CAMxWR_EN, 8-4
Cancel set actual value, 9-3
AVALREM_EN, 9-5
Canceling the setting, canceling actual value
setting, 9-5
CBEGIN, 8-28, 9-13
CE, mark, iv
CE marking, A-2
CEND, 8-28, 9-13
CH01CAM_EN, 9-11
CH16CAM_EN, 9-13
Change cam edges, 9-11
canceling, 9-12
data used in the channel DB, 9-11
definition, 9-11
effects, 9-12
requirements, 9-11
sequence, 9-11
Change of direction, at a cam, 2-9
Channel DB, 6-14
preparing, 7-5
structure, 6-15
task, 6-14
CNT_DIR, 8-19
CNT_LIM0, 8-24
CNT_LIM1, 8-24
Connecting cords, 4-5
Connection diagrams, B-1
Control signals, C-2
transferring, 6-5
writing, 6-22
Control signals for the cam controller, 9-29
data used in the channel DB, 9-29
sequence, 9-29
Controlling a press, 1-3
Count direction, 8-19
Index-2
Counted values of the counter cam tracks
data used in the channel DB, 9-25
data used in the parameter DB, 9-25
sequence, 9-25
Counter cam track, 2-6, 2-10, 8-24
upper counter value, 8-24
Counter cam tracks, counted values, 9-25
CPU, startup, 6-6
Creating a project, 7-2
CSA approvals, A-1
Current consumption, A-3
D
Data block, template, 6-14
Data check, 9-14
by the module, 9-14
Data errors, C-15
Data for "change cam edges" job, C-7
Data for "set actual value on-the-fly" job, C-7
Data for "set actual value" job, C-7
Data for "set reference point" job, C-7
Data for "zero offset" job, C-7
Data for the "fast cam parameter change" job,
C-8
Data for the "length measurement/edge
detection" job, C-8
Data for the "read cam and track data" job, C-8
Data for the "read counted values" job, C-8
Data for the "read encoder data" job, C-8
Data for the "read position and track data" job,
C-8
DC power supply, 4-3
Deactivate software limit switches
effects , 9-22
sequence, 9-22
Deactivating software limit switches,
SSW_OFF, 9-22
Delay time, total, 2-10
Diagnostic DB, 6-16
preparing, 7-5
structure, 6-16, C-12
task, 6-16
Diagnostic error, C-23
Diagnostic interrupt, evaluating, 6-18
Diagnostic interrupts, 11-4
entering state, 11-5
leaving state, 11-5
overview, 11-4
reaction of the FM 452, 11-4
FM 452 Electronic Cam Controller
C79000-G7076-C452-04