Satel PK-01 Manual
  1. Manuals
  2. Brands
  3. Satel Manuals
  4. Control Unit
  5. PK-01
  6. Manual

Satel PK-01 Manual

Standalone door control module
Hide thumbs
Table of Contents

Advertisement

Quick Links

Standalone door control module
PK-01
Firmware version 1.00
pk-01_en 06/12
SATEL sp. z o.o.
ul. Schuberta 79
80-172 Gdańsk
POLAND
tel. + 48 58 320 94 00
info@satel.pl
www.satel.eu

Advertisement

Table of Contents
loading

Related Manuals for Satel PK-01

Summary of Contents for Satel PK-01

  • Page 1 Standalone door control module PK-01 Firmware version 1.00 pk-01_en 06/12 SATEL sp. z o.o. ul. Schuberta 79 80-172 Gdańsk POLAND tel. + 48 58 320 94 00 info@satel.pl www.satel.eu...
  • Page 2 Changes, modifications or repairs not authorized by the manufacturer shall void your rights under the warranty. SATEL's goal is to continually improve the quality of its products, which may result in alterations of their technical specifications and firmware. Current information on the introduced modifications is available on our website.
  • Page 3 SATEL PK-01 The PK-01 module is designed for single door control. The access control is effected by means of electric control of the door status and user identification functions. 1. Features  Support for up to 50 proximity cards (wherever the word "card" is used in this manual, it means a passive transponder, which may take the form of a proximity card, proximity tag, etc.), and for 50 codes.

  • Page 4: Installation

    PK-01 SATEL When the code change and service functions are in use, the LEDs are used for communication with the user. 2.2 Keys The number keys and the keys are used for entering the code and starting the functions available in the module and for programming the module.

  • Page 5: Using The Module

    SATEL PK-01 5. Using the module 5.1 Unlocking the door 5.1.1 Unlocking the door with identifiers Bring the card close to the module (to a distance allowing the card to be read) or enter the code and confirm it with the key to start the procedure of user verification.

  • Page 6: Programming The Module

    PK-01 SATEL 5.5 Code change 1. Press the key, and then the key. The module will generate 2 short beeps and the green and red LEDs will start blinking simultaneously. 2. Enter the code and confirm with the key. The module will generate 2 short beeps.
  • Page 7 SATEL PK-01 Program relay operation time [7#] Configure relay operation time reducing function: [8#] disabled [0#] when door open [1#] when door closed [2#] Configure backlighting: [9#] [0#] automatic [1#] permanent [2#] When navigating through the service mode, keep the following principles in mind: 1.
  • Page 8 PK-01 SATEL 3. Confirm with the key. The module will generate 2 short beeps. The yellow LED will light 4. Press the key three times. 5. Confirm with the key. The module will generate 4 short beeps and 1 long beep.
  • Page 9 SATEL PK-01  the key – input supports NO type sensor. 3. Confirm with the key. The module will generate 4 short beeps and 1 long beep. Programming the request-to-exit input The request-to-exit input allows to unlock the door for the preprogrammed relay operating time.

  • Page 10: Specifications

    PK-01 SATEL  the key – permanent backlight. 3. Confirm with the key. The module will generate 4 short beeps and 1 long beep. 7. Restoring factory settin 1. Turn off the module power supply. 2. Short the ends of the green and black wires.

Table of Contents