Microtek ScanMaker s460 Start Here Manual
  1. Manuals
  2. Brands
  3. Microtek Manuals
  4. Scanner
  5. ScanMaker s460
  6. Start here manual

Microtek ScanMaker s460 Start Here Manual

Hide thumbs Also See for ScanMaker s460:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
Start Here
Installing your Microtek ScanMaker s460
Step 1:
Unpack your scanner package and check for
major components.
1. ScanMaker s460 scanner
2. Power adapter
3. Software CD
4. Hi-Speed USB cable
5. LightLid 35 Plus II*
* The LightLid 35 Plus II is either as a standard
equipment or an optional accessory depending
on the scanner configuration that you
purchased.
Step 2:
Important: Do not remove the yellow
stickers from your scanner until you are
told to do so. You must install software
before connecting your scanner.
Always close any open programs and turn
off Anti-virus utilities before installing
software.
A. Place the Microtek CD-ROM into the CD-ROM drive.
B. Follow the on-screen instructions to install the driver and software.
NOTE: If the Microtek Software Installer screen does not come up automatically, double-click the
following in succession: "My Computer"; the CD-ROM icon; then cdsetup.exe to start the installer
program.
Copyright © 2014 Microtek International, Inc. http://www.microtek.com
I49-004214 B, March 2014
Unpack Contents
Install Software
1
5
1
2
3
4

Advertisement

Table of Contents
loading

Related Manuals for Microtek ScanMaker s460

Summary of Contents for Microtek ScanMaker s460

  • Page 1 A. Place the Microtek CD-ROM into the CD-ROM drive. B. Follow the on-screen instructions to install the driver and software. NOTE: If the Microtek Software Installer screen does not come up automatically, double-click the following in succession: “My Computer”; the CD-ROM icon; then cdsetup.exe to start the installer program.

  • Page 2: Unlock Scanner

    Step 3: Unlock Scanner A. Remove the yellow “Step 3” sticker from your scanner. B. With the scanner power off, tilt the back left corner of the scanner to see the locking switch at the bottom. C. Push the locking switch to the position as indicated in the graphic, with the icon on the lock showing as “Unlocked”.

  • Page 3: Scanner Buttons

    Scanner Buttons The ScanMaker s460 is equipped with five scanner buttons, providing quick access to the most frequently used functions. These buttons are PDF, OCR, E-mail, Copy, and Scan. PDF: Scans the image and saves it in the Adobe Acrobat PDF format.

  • Page 4: Scanning Basics

    Scanning Basics NOTE: The scanning procedures outlined here make use of the Standard Control Panel in ScanWizard 5. To use the Advanced Control Panel, refer to the Supplement. 1. Place the scan material A. To scan photos, place the photo to be scanned on the scanner bed.
  • Page 5 Using the LightLid 35 Plus II NOTE: If your scanner configuration does not contain the LightLid 35 Plus II and you do not have intention to use this device, please ignore this section. Connecting the LightLid 35 Plus II 1. Remove the scanner lid. 2.

  • Page 6: Scanning Film

    Using the LightLid 35 Plus II (cont.) Scanning Film 1. Launch ScanWizard 5. In the Standard Control Panel, click the Original button. Choose “Negative Film” to scan negatives, or choose “Positive Film” to scan slides. 2. Click the Preview button in the Standard Control Panel to perform a preliminary scan of the image.
  • Page 7 Problems? The LED on the button panel indicates the status of the scanner. Flashing Ready to scan. Warming up or Scanner is off. scanning. If you encounter any problems, check the section below and follow the suggested solution if your problem is listed. You may also want to go over installation steps 1 to 4 of this "Start Here"...
  • Page 8 Finally, select and click the title of the manual you wish to view. Missing Items If your package is missing items, please call the Microtek Customer Service Department. Power Adapter Use only power supplies (AC/DC adapters) listed below:...

Table of Contents