Table of Contents
Advertisement
Quick Links
Start Here
Installing your Microtek ScanMaker s450/s350
Step 1:
Unpack your scanner package and check for
major components.
1. Scanner with built-in transparency adapter
2. Software CD
3. Power adapter
4. Hi-Speed USB cable
5. White mat
6. Film holder
Step 2:
Important: Do not remove the yellow stickers from
your scanner until you are told to do so. You must
install software before connecting your scanner.
Always close any open programs and turn off Anti-
virus utilities before installing software.
PC:
A. Place the Microtek CD-ROM into the CD-
ROM drive.
B. Follow the on-screen instructions to install
the driver and software.
NOTE: If the Microtek Software Installer screen
does not come up automatically, double-click the
following in succession: "My Computer"; the CD-
ROM icon; then cdsetup.exe to start the installer
program.
Copyright © 2007
Microtek International, Inc.
I49-004142 A, February 2007
Unpack Contents
Install Software
http://www.microtek.com
1
2
3
MAC:
A. Place the Microtek CD-ROM into the CD-
ROM drive and install all the software
components.
B. Restart your computer.
NOTE: After rebooting your Macintosh, the
Microtek software will attempt to locate your
scanner on the system. Since this is your first
install and you have not yet connected the
scanner, simply ignore the message that appears
and proceed to the next step.
1
6
5
4
Advertisement
Table of Contents
Related Manuals for Microtek ScanMaker s350
Summary of Contents for Microtek ScanMaker s350
- Page 1 Always close any open programs and turn off Anti- virus utilities before installing software. MAC: A. Place the Microtek CD-ROM into the CD- A. Place the Microtek CD-ROM into the CD- ROM drive. ROM drive and install all the software components.
-
Page 2: Unlock Scanner
Step 3: Unlock Scanner A. Remove the yellow “Step 3” sticker from your scanner. B. With the scanner power off, tilt the back right corner of the scanner to see the locking switch at the bottom. C. Push the locking switch to the position as indicated in the graphic, with the icon on the lock showing as “Unlocked”. -
Page 3: Scanner Buttons
PDF, and Custom. Cancel/Setup: Cancels the scanning job when the scanner is scanning. Launches the Microtek Scanner Configuration (MSC) utility when the scanner is not scanning. Scan: Captures images that can be saved as files or sent to an image-editing application. -
Page 4: Scanning Basics
Scanning Basics NOTE: The scanning procedures outlined here make use of the Standard Control Panel in ScanWizard 5. To use the Advanced Control Panel, refer to the Supplement. 1. Place the scan material A. To scan photos, place the photo to be scanned on the scanner bed. -
Page 5: Using The Film Holder
Using the Film Holder A. To load film: 1. Load the film inside the holder, with the film’s shiny base facing down. Slide the film along the slots of the holder until the film is fully loaded. 2. Raise the scanner lid, and place the film holder with the film on the scan bed. -
Page 6: Scanning Film
Using the Film Holder (cont.) Scanning Film 1. Launch ScanWizard 5. In the Standard Control Panel, click the Original button. Choose “Negative Film” to scan negatives, or choose “Positive Film” to scan slides. 2. Click the Preview button in the Standard Control Panel to perform a preliminary scan of the image. - Page 7 Problems? The LED on the button panel indicates the status of the scanner. Flashing Ready to scan. Warming up or scanning. Scanner is off. If you encounter any problems, check the section below and follow the suggested solution if your problem is listed. You may also want to go over installation steps 1 to 4 of this "Start Here"...
- Page 8 Finally, select and click the title of the manual you wish to view. Missing Items If your package is missing items, please call the Microtek Customer Service Department. Energy Star Notice As an ENERGY STAR Partner, Microtek International, Inc.
Need help?
Do you have a question about the ScanMaker s350 and is the answer not in the manual?
Questions and answers