Kenwood NX-5300 Service Manual page 84

Item Condition
Panel tuning
mode
[Analog 1) Adj item:
Wide [As ADEV]
4k] Adjust:[****]
*2 2) Adj item:
[Low1]→
[Low3]→
[Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
Press and hold
the [] key to en-
ter [Center1]
(Over Lap
High)→
Adjust:[****]
PTT : ON
Press [ ] key to
store the adjust-
ment value.
[Analog 1) Adj item:
Narrow] [An ADEV]
*2 Adjust:[****]
2) Adj item:
[Low1]→
[Low3]→
[Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
Press and hold
the [] key to en-
ter [Center1]
(Over Lap
High)→
Adjust:[****]
PTT : ON
Press [ ] key to
store the adjust-
ment value.
*2 : Refer to the "4.19.1 Necessary Deviation adjustment item for each signaling and mode" table.
Regarding Maximum Deviation (Analog), it is common with the adjustment of all analog signalings.
1-84 (No.RA015<Rev.002>)
Measurement
PC test mode Test-
equip-
ment
1) Adj item: Devia-
[Maxmum Deviation tion
(Analog Wide 4k)] meter
2) Adj item: Oscil-
[Low1]→ lo-
[Low3]→ scope
[Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
[Center1] (Over Lap
High)→
Press [Transmit]
button.
Press [Apply All]
button to store the
adjustment value.
1) Adj item: Devia-
[Maxmum Deviation tion
(Analog Narrow)] meter
2) Adj item: Oscil-
[Low1]→ lo-
[Low3]→ scope
[Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
[Center1] (Over Lap
High)→
Press [Transmit]
button.
Press [Apply All]
button to store the
adjustment value.
Unit Ter- Unit Parts
minal
Panel ANT Panel [Panel
tuning
mode]
[],
[]
[PC
test
mode]
[←],
[→]
Panel ANT Panel [Panel
tuning
mode]
[],
[]
[PC
test
mode]
[←],
[→]
Adjustment
Method
Write fixed value "494" 3310~3410Hz
for each adjustment
point. Transmit at each [PC test
adjustment point and mode]
check that the deviation Press [Apply
is between All] button to
3310Hz and 3410Hz. store the
Deviation meter adjustment
LPF: 15kHz value after all
HPF: OFF adjustment
points have
[Panel tuning mode] been adjust-
PTT: ON ed.
[PC test mode]
PTT: Press [Transmit]
button
Write fixed value "491" 2050~2150Hz
for each adjustment
point. Transmit at each [PC test
adjustment point and mode]
check that the deviation Press [Apply
is between All] button to
2050Hz and 2150Hz. store the
Deviation meter adjustment
LPF: 15kHz value after all
HPF: OFF adjustment
points have
[Panel tuning mode] been adjust-
PTT: ON ed.
[PC test mode]
PTT: Press [Transmit]
button
Specifica-
tions
/Remarks