Kenwood NX-5300 Service Manual page 37

Receive Assist, Transmit Assist
Tuning point Display
1 Low 1
2 Low 2
3 Low 3
4 Low 4
5 Low 5
6 Low 6
7 Center 1
8 Center 2
9 Center 3
10 Center 4
11 Center 5
12 High 1
13 High 2
14 High 3
15 High 4
16 High 5
17 High 6
4.3.4 Adjustment item supplement
Adjustment Item Description
Receive Assist The lock voltage of VCO (Receive) is ad-
justed.
This item must be adjusted before all ad-
justment items for receiver section are ad-
justed.
Transmit Assist The lock voltage of VCO (Transmit) is ad-
justed.
This item must be adjusted before all ad-
justment items for transmitter section are
adjusted.
Frequency Frequency is adjusted under receiving
condition with SSG.
The SSG needs 0.001ppm accuracy so
please use a standard oscillator if neces-
sary.
This item can be adjusted only in PC Test
Mode so that the adjustment value is not
changed easily.
Ramp Offset Adjust this item to the optimal Ramp volt-
age.
High Transmit High Transmit Power is adjusted.
Power
Medium Transmit Medium Transmit Power is adjusted.
Power
Low Transmit Low Transmit Power is adjusted.
Power
F2,F3,K2,K3
RX (MHz) TX (MHz)
450.050000 450.100000
454.450000 454.500000
458.850000 458.900000
463.250000 463.300000
467.550000 467.600000
471.950000 472.000000
476.350000 476.400000
480.750000 480.800000
485.050000 485.100000
489.450000 489.500000
493.850000 493.900000
498.250000 498.300000
502.550000 502.600000
506.950000 507.000000
511.350000 511.400000
515.750000 515.800000
519.950000 519.900000
F5,F6,K5,K6
RX (MHz) TX (MHz)
380.050000 380.100000
385.550000 385.600000
391.050000 391.100000
396.550000 396.600000
402.550000 402.600000
408.050000 408.100000
413.550000 413.600000
419.050000 419.100000
425.050000 425.100000
430.550000 430.600000
436.050000 436.100000
441.550000 441.600000
447.550000 447.600000
453.050000 453.100000
458.550000 458.600000
464.050000 464.100000
469.950000 469.900000
Adjustment Item Description
Balance The transmit modulation frequency re-
sponse is adjusted.
This item is adjusted so that the deviation
of 6kHz becomes the 96% deviation of
20Hz.
This item must be adjusted before all ad-
justment items for deviations are adjusted.
Maximum Deviation Maximum Deviation of P25/NXDN is ad-
(P25/NXDN) justed.
Maximum Deviation Maximum Deviation of Analog (Wide 5K/
(Analog Wide 5K/ Wide 4K/Narrow) is adjusted.
Wide 4K/Narrow) This item must be adjusted before all ad-
justment items for tone deviations are ad-
justed.
QT Deviation QT deviation is adjusted.
DQT Deviation DQT deviation is adjusted.
LTR Deviation LTR deviation is adjusted.
DTMF Deviation DTMF deviation is adjusted.
Single Tone Devia- The deviation of Single Tone used in "2-
tion tone" is adjusted.
MSK Deviation MSK tone deviation is adjusted.
CWID Deviation CWID tone deviation is adjusted.
CWID is used to inform the others who is
transmitting on a 6.25-kHz spacing chan-
nel. (In FCC rule, Analog mode or CWID is
required for each channel-spacing.)
Sensitivity 1 Band-Pass Filter is adjusted.
The performance of Receive Sensitivity is
improved.
(No.RA015<Rev.002>)1-37