Kenwood NX-5300 Service Manual page 48

Item Condition
Panel tuning
mode
2. 1) Adj item:
Ramp [RAMPD]
down Adjust:[****]
Offset PTT : ON
Press [ ] key to
store the adjust-
ment value.
3. 1) Adj item:
High [An H_PWR]
transmit Adjust:[****]
power 2) Adj item:
(Battery [Low1]→
voltage : [Low5]→
7.5V) [Center3]→
[High2]→
[High6]
Adjust:[****]
PTT : ON
Press [ ] key to
store the adjust-
ment value.
4. 1) Adj item:
Medium [An M_PWR]
transmit Adjust:[****]
power 2) Adj item:
(Battery [Low1]→
voltage :
[Low5]→
7.5V) [Center3]→
[High2]→
[High6]
Adjust:[****]
PTT : ON
Press [ ] key to
store the adjust-
ment value.
5. 1) Adj item:
Low [An L_PWR]
transmit Adjust:[****]
power 2) Adj item:
(Battery [Low1]→
voltage : [Low5]→
7.5V) [Center3]→
[High2]→
[High6]
Adjust:[****]
PTT : ON
Press [ ] key to
store the adjust-
ment value.
1-48 (No.RA015<Rev.002>)
Measurement
PC test mode Test-
equip-
ment
1) Adj item: Power
[Ramp Down Off- meter
set] Ammeter
Press [Transmit]
button.
Press [Apply]
button to store the
adjustment value.
1) Adj item: Power
[High Transmit meter
Power] Ammeter
2) Adj item:
[Low1]→
[Low5]→
[Center3]→
[High2]→
[High6]
Press [Transmit]
button.
Press [Apply All]
button to store the
adjustment value.
1) Adj item: Power
[Medium Transmit meter
Power] Ammeter
2) Adj item:
[Low1]→
[Low5]→
[Center3]→
[High2]→
[High6]
Press [Transmit]
button.
Press [Apply All]
button to store the
adjustment value.
1) Adj item: Power
[Low Transmit Pow- meter
er] Ammeter
2) Adj item:
[Low1]→
[Low5]→
[Center3]→
[High2]→
[High6]
Press [Transmit]
button.
Press [Apply All]
button to store the
adjustment value.
Unit Ter- Unit Parts
minal
Panel ANT Panel [Panel
tuning
mode]
[],
[]
[PC
test
mode]
[←],
[→]
Panel ANT Panel [Panel
tuning
mode]
[],
[]
[PC
test
mode]
[←],
[→]
Panel ANT Panel [Panel
tuning
mode]
[],
[]
[PC
test
mode]
[←],
[→]
Panel ANT Panel [Panel
tuning
mode]
[],
[]
[PC
test
mode]
[←],
[→]
Adjustment
Method
[PC test mode]
1) Set the adjustment
value to "1".
2) Increase the adjust-
ment value slowly while
monitoring the offset
monitor value.
3) Set the adjustment
value when the offset
monitor value exceed
"20".
5.0W ±0.1W 2.3A or
less
[PC test
mode]
Press [Apply
All] button to
store the
adjustment
value after all
adjustment
points have
been adjust-
ed.
Note: [PC test
Medium transmit pow- mode]
er is the purpose of Press [Apply
the custom power All] button to
(adjustment). store the
This power must be adjustment
lower than High trans- value after all
mit power. adjustment
In the production, this points have
Medium transmit pow- been adjust-
er is adjusted at same ed.
power as Low trans-
mit power.
1W ±0.1W 1.2A or
less
[PC test
mode]
Press [Apply
All] button to
store the
adjustment
value after all
adjustment
points have
been adjust-
ed.
Specifica-
tions
/Remarks