Kenwood NX-5300 Service Manual page 51

Item Condition
Panel tuning
mode
9. P25 1) Adj item:
H-CPM [P2 P2DEV]
Devia- Adjust:[****]
tion Deviation meter
LPF: 3kHz
HPF: OFF
2) Adj item:
[Low1]→
[Low3]→
[Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
*F5,F6,K5,K6
type only: Press
and hold the
[Right] key to en-
ter [Center1]
(Over Lap
High)→
Adjust:[****]
PTT : ON
Press [ ] key to
store the adjust-
ment value.
10. 1) Adj item:
NXDN [Nn NDEV]
High Adjust:[****]
Devia- Deviation meter
tion LPF: 3kHz
[NXDN HPF: OFF
Narrow] 2) Adj item:
[Low1]→
[Low3]→
[Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
*F5,F6,K5,K6
type only: Press
and hold the
[Right] key to en-
ter [Center1]
(Over Lap
High)→
Adjust:[****]
PTT : ON
Press [ ] key to
store the adjust-
ment value.
Measurement
PC test mode Test-
equip-
ment
1) Adj item: Devia-
[P25 H-CPM Devia- tion
tion] meter
Deviation meter Oscil-
LPF: 3kHz lo-
HPF: OFF scope
2) Adj item:
[Low1]→
[Low3]→
[Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
*F5,F6,K5,K6 type
only: [Center1]
(Over Lap High)→
Press [Transmit]
button.
Press [Apply All]
button to store the
adjustment value.
1) Adj item: Devia-
[NXDN High Devia- tion
tion (NXDN Narrow] meter
Deviation meter Oscil-
LPF: 3kHz lo-
HPF: OFF scope
2) Adj item:
[Low1]→
[Low3]→
[Low5]→
[Center1]→
[Center3]→
[Center5]→
[High2]→
[High4]→
[High6]
*F5,F6,K5,K6 type
only: [Center1]
(Over Lap High)→
Press [Transmit]
button.
Press [Apply All]
button to store the
adjustment value.
Unit Ter- Unit Parts
minal
Panel ANT Panel [Panel
tuning
mode]
[],
[]
[PC
test
mode]
[←],
[→]
Panel ANT Panel [Panel
tuning
mode]
[],
[]
[PC
test
mode]
[←],
[→]
Adjustment
Method
Write fixed value "498" 3090~3215Hz
(F2,F3,K2,K3),"497"
(F5,F6,K5,K6) for each [PC test
adjustment point. Trans- mode]
mit at each adjustment Press [Apply
point and check that the All] button to
deviation is between store the
3090Hz and 3215Hz. adjustment
Deviation meter value after all
LPF: 3kHz adjustment
HPF: OFF points have
been adjust-
[Panel tuning mode] ed.
PTT: ON
[PC test mode]
PTT: Press [Transmit]
button
Write fixed value "497" 2995~3117Hz
for each adjustment
point. Transmit at each [PC test
adjustment point and mode]
check that the deviation Press [Apply
is between 2995Hz and All] button to
3117Hz. store the
Deviation meter adjustment
LPF: 3kHz value after all
HPF: OFF adjustment
points have
[Panel tuning mode] been adjust-
PTT: ON ed.
[PC test mode]
PTT: Press [Transmit]
button
(No.RA015<Rev.002>)1-51
Specifica-
tions
/Remarks