Related Manuals for Yetter 10000 Magnum Series
Summary of Contents for Yetter 10000 Magnum Series
- Page 1 ™ 10000 SERIES MAGNUM FERTILIZER COULTER 2565-957_Rev_D 02/2018 YETTER MANUFACTRURING CO. Founded 1930 Colchester, IL 62326-0358 Toll free: 800-447-5777 Fax: 309-776-3222 Website: www.yetterco.com Email: info@yetterco.com...
-
Page 2: Foreword
WARRANTY Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This warranty being expressly limited to replacement at the factory of such parts or products as shall appear to be defective after inspection. This warranty does not obligate the Company to bear cost of labor in replacement of parts. -
Page 3: Table Of Contents
TABLE OF CONTENTS Foreword ..................... 2 Safety ......................4 Torque ......................5 General Information ................. 6-7 Assembly Instructions ................8-9 Operation ....................10-12 Troubleshooting ..................13 Maintenance ..................14-18 Part Identification ................19-44 Photo Album ..................45-47... -
Page 4: Safety
BE ALERT! YOUR SAFETY IS INVOLVED. WATCH FOR THIS SYMBOL. IT POINTS OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS “ATTENTION---BECOME ALERT!” It is your responsibility as an owner, operator, or supervisor to know and instruct everyone using this machine at the time of initial assignment and at least annually thereafter, of the proper operation, precautions, and work hazards which exist in the operation of the machine in accordance with OSHA regulations. -
Page 5: Torque
BOLT TORQUE ™ Before operating the 10000 Series Magnum for the first time, check to be sure that all hardware is tight. Check all hardware again after approximately 50 hours of operation and at the beginning of each planting season. ™... -
Page 6: General Information
GENERAL INFORMATION 10000 Series Magnum Fertilizer Coulter STANDARD FEATURES FOR ALL MODELS High application speeds with minimal soil disturbance for fall, pre- • plant, and side-dressing applications Tube kits for applying liquid, dry, or anhydrous • All cast design • Spring loaded knife with carbide tip for extended wear •... -
Page 7: General Information
GENERAL INFORMATION 10000 Magnum Fertilizer Coulter... -
Page 8: Assembly Instructions
Example: A 30’ – 3 section toolbar with 12 coulters (6R & 6L) will need to install 2R and 2L coulters on each section of the toolbar. If any questions concerning assembly of coulters, then please contact Yetter Farm Equipment for recommendations at 800-447-5777. -
Page 9: Part Identification
ASSEMBLY INSTRUCTIONS STEP 2: Attach the 10000 Series Magnum to the toolbar using the appropriate clamp and hardware. HARDWARE KITS PART IDENTIFICATION... -
Page 10: Operation
OPERATION INSTRUCTIONS TOOLBAR FRAME HEIGHT ADJUSTMENT Adjusting Opener Depth: -Raise toolbar frame for shallow application -Lower toolbar frame for deeper application Figure A: The toolbar height is set to 25” above the soil surface. To ensure that frame heights are correct, it is important measurements are taken before use. Figure B: The hitch is set too low while the toolbar is not parallel with the soil surface. - Page 11 OPERATION INSTRUCTIONS 10000 MAGNUM CLOSING WHEEL DOWNFORCE ADJUSTMENT...
-
Page 12: Operation
OPERATION INSTRUCTIONS 10000 MAGNUM WHEEL SEALER DEPTH ADJUSTMENT... -
Page 13: Troubleshooting
OPERATION INSTRUCTIONS Troubleshooting the 10000 Series Magnum Coulter Symptom Problem Solution Too much down pressure Remove spring pressure Mud builds up on press from press wheels wheels and wheels stop turning Field is too wet Wait until field dries before running Hard ground conditions Add weights to toolbar... -
Page 14: Maintenance
MAINTENANCE Practice Safety Understand and practice safe service procedures before doing work. Follow ALL the operating, maintenance, and safety information in the equipment operator’s manual. Clear the area of bystanders, especially small children, when performing any maintenance or adjustments. Keep work area clean and dry. Use adequate lighting for the job. - Page 15 MAINTENANCE Lubrication Intervals Lubricate with grease at hourly interval indicated on symbol. IMPORTANT: The recommended service intervals are based on normal oberating conditions. Severe or unusual conditions may requre more frequent lubrication. Perform each lubrication and service procedure at the beginning and each of each season.
- Page 16 Alternative Lubricants Conditions in certain geographical areas may require special lubricants and lubrication practices which do not appear in the operator’s manual. If there are any questions, consult Yetter Manufacturing Co. to obtain the latest information and reccomendations. Part # Description...
- Page 17 • Clean machine thoroughly to remove all dirt, debris, and crop residue. • Inspect machine for worn or broken parts. See your Yetter Farm Equipment dealer during the off-season so parts and service can be acquired when the machine is not needed in the field.
-
Page 18: Maintenance
MAINTENANCE BEARING ADJUSTMENT: 1. Raise the toolbar until the blade is clear of the ground. Place a safety stand under the toolbar. Remove the blade. Remove the hub cap, cotter pin, slotted nut, washer and spacer from the spindle shaft assembly. 2. - Page 24 MANUFACTURED 7/2016 – 2/2018...
- Page 25 MANUFACTURED 7/2016 – 2/2018...
- Page 26 PART IDENTIFICATION 10000-100-LH MANUFACTURED 3/2018 - PRESENT...
- Page 27 PART IDENTIFICATION 10000-100-LH MANUFACTURED 3/2018 - PRESENT...
- Page 28 PART IDENTIFICATION 10000-100-RH MANUFACTURED 3/2018 - PRESENT...
- Page 29 PART IDENTIFICATION 10000-100-RH MANUFACTURED 3/2018 - PRESENT...
- Page 48 Our name Is getting known Just a few years ago, Yetter products were sold primarily to the Midwest only. Then we embarked on a program of expansion and moved into the East, the South, the West and now north into Canada. We’re even getting orders from as far away as Australia and Africa.